micro swiss direct drive 3d models

Thus, I was searching for a extruder knob for my Micro Swiss DD and found the design from tlr1000 (credits to him!). As I had no brass fitting at hand for mounting the knob to the shaft, I made that remix with a press fit mount like on many other...

Slots are sized for M3 screws, designed to replace MicroSwiss Bowden tube adapter for the Ender 3 MicroSwiss direct drive modification. This is a remix on the "Ender 3 Cable Chain, no screws, no unplug cable" by NG_Design. Their mount on the z axis...

This custom creation, adapted from the MS direct drive remix, now incorporates a 5015 fan and a 4020 hotend fan. Some compromises were made to fit these components in place of others. Despite not being perfect, it still prints without issues and has...

This small block attaches to the flat metal section directly opposite the extruder and engages the X-axis switch without requiring further modifications. By combining this with a slight forward movement of the Y-axis switch, you won't need to...

Das ist ein Remix von https://www.thingiverse.com/thing:4101494 und https://www.thingiverse.com/thing:4389912 Habe nur die Öffnung etwas vergrößert und eine Halterung für die Kabel eingefügt, damit sie nach links liegen. ...

Added a bracket for a cablechain. ...I also rounded a few corners for looks and clearanced a section on the right side that was very close to the heater block

Hotend Mount for Chain Cable - Ender 5 Plus

This is a simple hotend wire harness for the new MS DD NG. ...You need to install this prior to installing the V-Slot wheels.

Printed with carbon fibre PETG at .2mm layer height. No supports. Skirt. This would work just fine with any filament type, i.e. PLA. I used thread lock instead of the lock washers. You will need some 6mm cap head M3 bolts to attach to carriage. If...

I loved the original design of this but was using a cable chain so I didn't have a use for the existing channels (remix from https://www.thingiverse.com/thing:4187151). I just remixed it to fit the extruder and added a cable mount (pulled from...

You can buy in any store switch and insert in this model. You need to make with drill started holes for switch, and if you want to put PTFE in you need to make bigger hole with drill :) In the end its works perfect! ... PETG 0.2mm

This is a simple hotend wire harness for the new MS DD NG. You need to install this prior to installing the V-Slot wheels. ...

Remixed a Support flaw in the upper deck. This will print better with more support on the right side to stop the warpage when it forms the upper deck. added holes for cable ties. ... *V2 has Fixed holes for the fan mount as the original holes didn't...

The bracket that's included with the Micro Swiss Direct Drive Extruder for Creality CR-10 / Ender 3 Printers.

... Extruder for Creality CR-10 / Ender 3 Printers. ... https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder Nice and secure mounting under the heat brake, I applied a dab of crazy glue at the bottom, just for added security. ...

Adaptor to mount Micro Swiss Direct drive for Ender 3 Pro to 3DFused linear rail X-axis gantry kit used in conjunction with thing:4582867 (Hero Me Gen5 mod for Ender 5 Plus with Micro Swiss Direct Drive and Hotend ). ...This allows for BL Touch and twin...

Modified version where the cutout for the fan shroud is larger. ... I have the most recent version of the Micro Swiss Direct Drive and my fan shroud caused the original to not be flat.

Just a remix to hold the bed level sensor so you can install a micro swiss direct drive all metal hot end on an ET4 pro. ...This does require a slimmer stepper motor for the extruder.

Fan shroud used to install the Micro Swiss Direct Drive Extruder (M2602) and CR-10S Pro All Metal Hotend (M2591) onto a Creality CR-10S Pro (V1) using the original proximity sensor.

Fan Shroud Adapter and PTFE Guide Tube Bracket used to install the Micro Swiss Direct Drive Extruder kit on an Ender 3 Max. ... The PTFE bracket will align the PTFE tube with the Ender 3 Max filament runout sensor.

It is a remix of https://www.thingiverse.com/thing:4369859 to fit Micro-Swiss Direct Drive for Ender 3 Pro. ... Offset for my extruder: X-49.8 Y-09.3 Z-2.80

This is a REMIX/COMBINATION of [Micro Swiss Direct Drive EZOut v2 Mount](https://www.thingiverse.com/thing:4232736) [Ender 5 Plus Linear Rail Conversion](https://www.thingiverse.com/thing:4578889) [Ender Filament Runout...

Remixed to Support Micro Swiss Direct drive kit for Creality machines. Carriage mount had its cable chain connection shifted to avoid the stepper motor that sits over the wheels with the Micro Swiss kit. ...As a result, the gantry cover was modified to...

This is a modified base for the Ender 3 V2 with the Micro Swiss Direct Drive upgrade. The rest is printed from the BullEye stl's. https://www.thingiverse.com/thing:2759439 I've changed the cable management, that was interfering with the direct drive...

Remixed from - Satsana dual fan remix by BobanaPirate to fit on my Ender-3 Max with the Micro Swiss direct drive extruder. Changes made: removed the clip that held the cables up above the fan shroud because it interfered with the direct drive...

Adaptor to mount Micro Swiss Direct drive for Ender 3 Pro to 3DFused linear rail X-axis gantry kit. Suits standard Ender 3 fan set up with or without BL Touch. ... Shims may be needed with BL Touch depending on the x-axis limit switch set up.

Very basic extruder fan and blower mount for the Ender 3 V2, to be used with the Micro-Swiss Direct Drive Extruder kit (which did not have an official fan mount as of 1/2022). ... Includes cable fork to hang the cable bundle out of the way of the...

Very basic extruder fan and blower mount for the Ender 3 V2, to be used with the Micro-Swiss Direct Drive Extruder kit (which did not have an official fan mount as of 1/2022). ... Includes cable fork to hang the cable bundle out of the way of the...

... ... This moves the Y endstop 6.5mm to truly allign the bed. I also added X-Y-Z since i always forget that... NO MORE! Check my other designs for the X endstop. Printer: Creality Cr-10s pro v2 Mod: Micro swiss direct drive extruder with hotend