micro swiss direct drive 3d models

This is a remix for the bullseye base redesigned to fit perfectly on to the Micro Swiss Direct Drive Kit. ... Enjoy!

... based on madbuda's innovative design. ... Fitted with a compact wire harness for improved accessibility and reduced clutter. Designed specifically for the Micro Swiss Direct Drive, this upgraded component is compatible with Ender 3/3 Pro models.

A hot end bracket for the Micro Swiss Direct drive to attach cable/drag chain to on Ender 3/pro 3d printers. ...it works well with no loss of travel in the X axis

Ender 5 Plus Micro Swiss Direct Drive Palette Connector If you find it usful and would like to donate anything here is my PayPal https://www.paypal.com/biz/fund?id=QPA2FV7N6SRRC

I modified the hero me gen 4 base to be compatible with the Micro Swiss Direct Drive, and it's functioning properly. ... v2 09/05/2020: I fixed a gap near the screws.

Crafted a custom extruder knob specifically tailored to fit my micro Swiss direct drive extruder - and now it's in action, with the entire assembly moving in perfect harmony as I print.

... printers. ...It merges the backplate from Akanar's design with Baird1fa's Micro Swiss direct drive adapter for Ender 5, requiring users to drill out one mounting hole since the combination was done in Cura by simply mashing these two designs together.

Video Instructions on How to Upgrade Micro Swiss Direct Drive for the Ender 3 - https://www.youtube.com/watch?v=8iAuBYfwLvg Here a link to the bltouch mount - https://www.thingiverse.com/thing:4644075 Donations Via Paypal are not necessary, but...

A simple cable strain relief for the Micro Swiss Direct Drive (Ender 5 version). It prints with no supports and can be mounted directly onto the aluminum plate using a screw. FreeCAD file included, so you could easily adapt it for your needs. ... If...

Sensor mount for the Creality Sonic Pad that mounts on the right side of the Micro Swiss Direct Drive plate. Pretty easy to put on and take off. ...A few small zip ties secures the sensor to the bracket, then screw to the plate and calibrate.

Here's a remix of the original thing from Thingiverse, tailored to fit my Micro-Swiss Direct Drive for Ender 3 Pro. To get my extruder aligned properly, I'm using an offset of X-45.15, Y-8.28, and Z-2.40. ... The mount I've chosen is available here:...

My adaptation of the Hero Me Gen 5 for a Micro Swiss Direct Drive mount on an Ender 5. Optional mount on the side for a BLTouch. Parts are designed to use M3 X D5.0 X L4.0 heat set inserts instead of pocketed nuts. I used the same inserts as most...

This is a simple design to be able to install the hot end fan and the part fan on a new Micro Swiss Direct Drive. Since the original hard ware will not fit the new part, here is a solution. ... Just change the parts Fan Nozzle 4 mm and centered with the...

I was looking for a satsana fan duct but I was not able to find one able to satisfy my requirements: mounting on Micro swiss direct drive for ender 3, fitting BLtouch and using 2 noctua 4020 for hot-end cooling and part cooling. ...so I did my own yet...

Designed for the Micro-Swiss Direct Drive Extruders on Voxelab Aquila 3D Printers, Specially, it adds an "nub" to hit the x-axis stop sensor. Supports a 40x40x10mm fan and 5010 blower fan. ...Holes for M3 threaded inserts 4x5mm are available.

With the Micro Swiss direct drive extruder on the Ender-3 printer the Z-axis is somewhat reduced. ...With this cable chain mounts the cables and filament are running in front of the frame so you can achieve 200mm build height.The top and bottom parts...

... with spacers to adjust the Z. On the Micro Swiss Direct drive there was no need for the cut out area so I removed it to increase strength. This will print with no supports . ... Settings Y: -17.5 mm X: -43.8 mm and Z will depend on spacers used.

I used the KentoHardRok adapter to perform my Micro Swiss direct-drive upgrade to my CR10S Pro v1 and found that that both mounts for the BLTouch referenced from the remixed design exceeded the sensor offset limits on the firmware used. I modeled a...

Fang base plate for the Micro Swiss Direct Drive + MS Hot End (Ender 5 Version). Use the following "fang"-duct: https://www.thingiverse.com/thing:4389912 ...and for the 40mm fan: https://www.thingiverse.com/thing:2763931 Offsets: x: -54 ...

This is an upgrade for my Micro Swiss Direct Drive EZOut v2 Mount: https://www.thingiverse.com/thing:4232736 Step files are included. This installs between the EZOut Mount and the Bowden Tube on that mount. Insert a small amount of cotton or...

Mounting plate for use on the Micro-Swiss direct drive extruder plate for the DyzeEnd X hotend. Will work with water cooling, or air-cooled with the stock Dyze Design cooling fan. Uses the stock Ender 5 BLTouch mount and hardware. You will need...

I'm reposting this micro Swiss adapter plate for direct use with a Micro Swiss direct drive on my Ender5. Someone else created it, but I couldn't find the original post to give credit where due. My apologies, but hopefully others will find it just as...

This thing will properly support the bundle of cables coming off of your Micro Swiss direct drive and hot end. The direct drive support clips directly to the carriage axles, while the X-axis support clips to the stock Ender 3 plastic cover near the...

Fang mount for Micro Swiss Direct Drive. This base is designed specifically for the micro swiss hot end. To assemble this mount, you'll need to print the fan and 40mm fan duct from https://www.thingiverse.com/thing:2763931. I ended up needing t m3...

Mini+CR Touch Mini+Endo+CR Touch Designed this for my Ender 3 V2 that is using Micro Swiss direct drive extruder. The one Micro Swiss recommends weighs more than I liked. Uses the stock fans. This design allows the use of three M3*8 bolts to...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

I installed this on a customized Longer LK4 Pro (sort of an Ender 3 clone), hence it should fit any Ender 3 version that has been modified with a Micro-Swiss Direct Drive extruder, and probably other printers as well. I used standard 40x40mm...

This is a hastily crafted adaptation of the hero me gen 2 tailored specifically for the mosquito hot end to be paired with a micro swiss direct drive extruder. Being entirely new to design, I relied on tinker cad to customize Mediaman's original...

The one that he made works with the stock Ender 5, but recently I upgraded to a Micro Swiss direct drive extruder. The mount that he designed hits the spot where the belt is attached to the carriage plate. The mount doesn't hit the belt clip now...

Upgrading to the micro Swiss direct drive kit for the Ender 3? This extruder knob reclaims the original brass extruder gear as its core component. I grew weary of extruder knobs relying solely on plastic contact points, which can be easily rounded...