mic stands for blue snowball 3d models

Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...

Blue Snowball Mic

I needed a compact pop filter for my Snowball mic and wasn't willing to shell out $20 for a few dollars' worth of plastic, so I decided to print two mesh holders, attach a thin piece of fabric or mesh between them before assembling the model itself.

This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.

... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...

I remixed a haxespot lamp to accommodate my blue snowball microphone, attaching it via a threading adapter borrowed from another user. I also created custom couplers to connect to the arm's end, ensuring a rock-solid setup. While the mic couplers are...

The Blue Snowball leg joint on the stand is not that strong. Designed in Fusion 360, simply print and screw in the new one. ... 30-40% infill with .2 layer height gives plenty of strength using PLA.

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...

This is a replacement part for the Blue Snowball mic stand. Factory plastic parts on the legs are subjected to considerable pressure, making them prone to breaking. To create this part, simply print with an infill of about 35-40%. No supports are...

I built a custom microphone stand for my Yeti Blue Snowball mic, giving it a sleeker look by making it shorter. ...The USB cable posed an issue due to its downward angle, but I found a solution that provides ample clearance for the cord while also...

An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small footprint...

Mount the Blue Snowball to your table lamp stand using this part.

... TV, tilt it to suit your specific setup. ...Specifically designed for the Blue Snowball microphone, this configuration ensures optimal placement. ...To create this setup using a 3D printer, use PLA filament and set the infill percentage between 10-20%.

This is a remix of a couple of shockmounts I found on Thingiverse.My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand.One M3 screw is needed for mounting the outer ring to the threaded part. And of...

The main improvement is that this new design can be used on the original Blue Snowball microphone stand. To assemble it, you'll need one M3 screw to attach the outer ring to the threaded part, as well as some rubber bands or hair ties to secure your...

Made this to keep my Blue Snowball microphone from sliding off the desk and causing chaos. Enjoy! ...Threads made possible by: https://www.thingiverse.com/thing:193647 Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: None Required...

I remixed the threads from  https://www.thingiverse.com/thing:3766117 onto a simple base plate for a tripod.

I remixed the threads from  https://www.thingiverse.com/thing:3766117 onto a simple base plate for a tripod.

This is a simple gadget to attach any Blue Snowball (or other) microphone to a standard "lamp arm" and it also includes a built-in pop filter. The bird, however, is not included. You'll need to glue Arm_long.stl and ring_center.stl together. I've...

... presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

... a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. ... It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the back-center. ... A M3-.50 nut is required.

Adhesive pads for furniture legs provide a durable alternative to traditional rubber feet, ensuring stability and preventing scratching on delicate surfaces.

After testing several microphones for podcasting, a Samson Go Mic emerged as my top choice. I had an adjustable arm from another microphone that I wanted to utilize to both position and isolate the mic from background noise. To integrate this...

This is a short desk stand for the Blue Snowball microphone. I designed this to be able to fit the mic below my monitors. The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the...

The compact blue Snowball microphone stands 10 millimeters tall on its slender stand.

A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...

I designed this tiny shock mount that uses rubber bands for dampening to replace the bulky Blue Snowball's regular stand. It allows you to see past it easily. You'll need a small pipe from the microphone's desk stand (which comes with the mic) and...

Initially, I attempted to print ad895's version from Thingiverse (https://www.thingiverse.com/thing:2225557), but it fell short for my Blue Snowball due to a mount that was too short and a hole that was excessively wide. When this didn't yield the...

This is a mounting bracket for the Black Ice Snowball to attach to the HP Z24i. You just unscrew the original tripod and screw this on. ... The mic hangs upsidedown from the bottom of the monitor.