meshlicious itx case 3d models

This PC enclosure boasted no mounts for a cooling fan. To create airflow within the system, an ingenious fan holder was necessary - essentially a mobile cradle that freely oscillates, enabling a gentle breeze to flow through one side panel. ...A few...

Measurements for this item are 180mm x 110mm x 280mm. ...It can accommodate a GPU of up to 300mm and a CPU cooler of upto 45mm in height.

 Additionally you'll need to either remove and reuse the 5 plastic clips attached to the case, or (my recommendation) print 5 of RGI's Meshlicious Clips and snap them into the square holes of the extension part.I also recommend you print the...

A PC case featuring an ITX form factor, excluding a built-in graphics card.

A support designed for the rear GPU finger in a Meshlicious case.  Gives more surface area to support the bracket from bending.  This is meant to be used when the GPU is in the higher position and in 4-slot mode.Currently this design is slightly...

This is a DDC pump bracket to fix a ddc pump on the bottom of the SSUPD Meshlicious if the screw holes of the pump mounting don't line up with the case holes. You can fix M3 screws on the bracket first by putting nuts in the wider holes and then...

The SSUPD Meshlicious fan holder is inspired from chaosmage project. I have optimized the holder to be more stable and is not blocking any airflow. Fits perfectly for 92mm Noctua fans. ...

This is a remix (not a very good one) of a popular design for SSUPD Meshlicious. ...It's edited to fin in 3 slot GPU big Big cpu cooler motherboard config

This is a mini ITX case.It is compatible with a full size CPU cooler, a 205mm long GPU, and an ATX PSU.

The SSUPD Meshlicious fan mount is inspired from chaosmage project.I have optimized the holder to be more stable and is not blocking any airflow. With this fan mount you could improve the VRM and mainboard cooling.Fits perfectly for 92mm Noctua...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/kHY7XI2IVQn case big enough for PICO-ITX.

This is an unfinished mini ITX case designed specifically for Gigabyte motherboard GA-H77N-WIFI, and I am currently in the process of completing it.

This is designed to be a replacement panel for the rear of the SSUPD Meshlicious where the PCI slots are. This panel allows you to use Koolance QD3 panel couplers. The panel couplers have M18x1 threads which is the same used here. I loosened the...

Maybe print just the part for the gpu and check it before you print the entire thing :DCheck my previous remix of the vl4dt3p3s's ITX PC CASE to see how I split the print into two pieces and glued it.This is a dual slot low profile GPU, ITX...

A small mini itx pc case that can house a single bracket half slot gpu. Printed using PETG on ender 3 with no support. The longest part is 19.5cm (195mm) long and It is separated into three parts, the mother board tray, outer shell and side panel.

Here are the components I used to bring the Borg Case to life: * Motherboard: ASRock H270M-ITX/ac LGA 1151 motherboard (discontinued, but any mini-ITX motherboard should fit) * Power Supply: FSP 450W Mini ITX Solution/SFX 12V / Micro ATX 80 Plus...

The .stl has been modified to remove the middle supports of the case that are specific to coinmine motherboards to accommodate any MIni-ITX MB. The files with the label "coinmine" in the file name is specific for the coinmine MB and can't be...

This is used to mount a makerspot USB otg hub to the inside of a mini itx case for a MiSTer FPGA build. I used 100% infill. Case used... https://www.amazon.com/gp/product/B07HCCTMNZ/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 USB hub...

Held to the case with existing 3mm holes. The PCIE riser is not held by anything. There needs to be a new hole created for the right bracket bottom most hole. ...Then use the existing standoffs with a 6-32 - 3/4inch screws to attach the standoff to...

... printers use. ... The motherboard is a Gigabyte AB350 gaming WIFI Mini ITX, I'm unsure if other motherboards will work because the socket location may be different. ... There is no hole for a power button, so you'll need to drill one wherever you like.

By utilizing this conversion kit, users can install USB ports in the controller's slots, replace the video adapter with an HDMI port, attach the Mini-ITX motherboard to the original Xbox mounting points, and utilize the existing power hole on the...

Mini-ITX case designed from the ground up with the chip shortage in mind. AMD release of the Ryzen 5600G and 5700G finally motivated me to design a 3D-printed PC case. I wanted a more traditional yet proven design built for dustless airflow (from...

This case is specifically designed for mini-ITX builds. The holes on the front panel are strategically placed for: * A 15mm momentary power button * A 5mm LED holder and LED * Screw-mount USB ports Meanwhile, the holes on the back panel accommodate:...

This is an External Case for a Gigabyte Mini-ITX GTX 970 (GV-N970IXOC-4GD) and the EXP GDC External Video Card Adapter (v8.0), allowing me to run my card externally on my laptop. I use this setup primarily for a portable Oculus Rift laptop, so I've...

Tried to find a 10 inch rack mount Mini-ITX computer case for my PFsense build. But coudn't find one on the market in the EU or here on thingiverse. So I designed my own. Features: - 2U 10 inch rack mountable - Fits a Mini-ITX motherboard - 1 low...

Fully printed on a 3D printer in ITX format computer case To build it requires the skills of working with electricity and computer components Adapted size and shape for printing on a 3D printer up to a maximum print area of 200x200x200 mm Printing...

It can fit: - ITX motherboard with all its components and an air cooler (no support for AIO liquid coolers at the moment) - One PCIe card (GPU or else) (---NEW REVISION--- NEEDS TO BE TESTED FOR DIMENSIONAL ACCURACY) - Two 2.5in SSD / HDD - I left...

Fully 3D Printable Mini ITX computer case. FULL VIDEO: https://youtu.be/WKnhARips-w Features: - Graphics Cards up to 270mm - Bottom to top ventilation - Mounts for ATX power supply (depth max 125mm) - Mounts for 3.5" HDD - Unique clean design...

The magnet holders are printed individually and bonded with hot glue, which is necessary due to the compact size of this case - just slightly larger than mini-ITX mobo specs, so the motherboard will not fit if the magnet holders are attached to the...