mendelmax 3 3d models

... if cords or panels are nearby like this example: http://www.thingiverse.com/thing:27354. ...Printing instructions include attaching the part to your motor and trimming extra feet if necessary. This design is tailored for MendelMax 1.5 motor mounts.

To fabricate a Y-axis frame for a MendelMax 3D printer, laser cut 6.35mm (1/4") thick wooden sheets. Remember, as the heated table is positioned on the carriage, avoid using plastic materials to prevent melting and deformation. ...Ensure accurate...

Attach a 120mm fan to your MendelMax or similar machines using this mount, along with materials including two M4x50mm screws, an M4x60mm bolt (preferably with hex head), five M4 nuts (or six if a rod is used instead of the long bolt), an M5x30mm...

This support is designed specifically for Arduino Mega and Ramps 1.4 boards, allowing you to conceal electronic components within your Mendelmax 3D printer. Print it without support (as "support arduino") or with support for the two clips (as...

The 2020 Misumi Clip is essential for the MendelMax build, try checking out blackllama's improved design (#40581) on Thingiverse. Due to issues with initial printing, I fixed this model using Netfabb and successfully printed it. ...Check it out at...

The Mendelmax 1.5 is equipped with a simple yet effective spool holder. ...To achieve this, I opted for a 16mm carbon tube as the shaft, opting not to incorporate a bearing into the design, and it functions perfectly well without one.

The Y-rod holder is inspired by ziptie-less LM8UU holders designed for MendelMax printers and compatible with Aluminum Extrusions. In contrast to MendelMax v1's Y-rod holders, which spanned two extrusions, v1.5 features a lasercut piece attached to...

The tensioner matches the original Mendelmax 1.5 bracket but may require washers for Simonious' wider version. Be sure to use the longest screws possible for the hinge pin to minimize play. ...Note that this design is a work in progress and new...

When deciding on which upgrade route is right for you, consider that some Mendelmax variants are designed with specific end stops in mind. Ensure you choose a method suitable for your specific setup and do not mix parts unless explicitly specified...

An improved version of Phaiax's spool holder is presented here, designed for compatibility with MendelMax 1.5 and other printers built on aluminum extrusion. The original mount was insufficient for larger spools, causing damage to the support; thus,...

The bracket incorporates a 20mm mounting hole for an emergency stop button, compatible with 20mm Mitsumi extrusions found on MendelMax. Securely install your emergency switch through the hole and fasten it using two 4mm screws to the extrusion. ...For...

Revamped set of endstop holders for a MendelMax 2, featuring RRD / Rumba Mechanical Endstops. Employs 5mm and 3mm fasteners. Upgraded from original design to maintain design consistency and deliver enhancements such as: X-Axis Mount: Adjusted...

The MendelMax clip's design has been slightly modified to make it thinner while increasing the length of its teeth for a tighter fit with the extrusions of this printer. These clips can be easily twisted into place, and they require minimal printing...

My trusty Mendelmax 1.5 has served me well, but its height limitations are becoming a major constraint. This straightforward upgrade takes what I already have and adds some much-needed inches. Before diving into a full-scale build, it's essential to...

For endstops, I used those available at store.mendelmax.com. Photos should aid understanding. Start by cleaning the part if necessary, then insert the endstop before sliding it onto the bolt holding the Wade's extruder in place. ...Add a washer and a...

To maintain 10 cm and 8 cm wide spools on my MendelMax 1.5, I designed supports. Each support requires an 8 mm M3 socket head bolt, a drop-in nut (http://www.thingiverse.com/thing:245103), and a 15 mm M6 bolt with a 6 mm inner diameter and 17 mm...

I designed these supports to securely hold ten and eight centimeter wide spools on top of my MendelMax 1.5. Each support features an eight millimeter long M3 socket head bolt, a drop-in nut (http://www.thingiverse.com/thing:245103), a fifteen...

X End Motor and Idler - created by Prusa and edited to fit the Mendelmax 3d printer - distance between bearings and trapezoidal nut increased to 30mm - added screws to tighten the bearings2. Extruder - created by Prusa and modified by Bondtech...

A duct for the power supply fan on a Mendelmax 2.0 3D printer. Normally the exhaust from the power supply fan blows directly upwards onto the underneath of the heated bed. This duct will redirect it out the side of the base of the printer. The duct...

I constructed three build plates for a 200 x 200mm MendelMax 1.5, including components such as Lower Vertex (Lower Left x2, Lower Right x2, Upper Left x2, Upper Right x2), Top Vertex (X, no logo x4), Y_Motor_Mount x1, Y-Idler-mount x1,...

Revise MendelMax spool holder prototype Although not the final design, suggestions are welcome. This is Version 7 of the spool mounts. They offer increased stability due to their length. Although holes for #5 screws and bearing attachment are...

A derivative is available for Mendelmax and dial gauge with a .37" or 9.5mm shaft. Holes are removed to secure the shaft, creating a press fit. The 123D file is provided for editing purposes if required. After printing, test fit the gauge and make...

A custom-designed fan mount is being developed specifically for a 15mm by 50mm blower fan to be utilized within the MendelMax 1.5 system. The primary goal of this project is to optimize airflow and improve overall print quality while also minimizing...

To enhance the print quality on my MendelMax 2.0 printer, I observed that a Replicator 2's fan significantly improves results. Initially, I used two angled fans with mounts (http://www.thingiverse.com/thing:139952). Later, I developed a thicker fan...

Designed to mount across the bottom extrusions or in the bottom corners (see photos). You can find the openscad file at github. Instructions Uses M5 10mm bolts with washers for the tabs (and t-nuts) and M3 20mm bolts for the side bolts. Before...

This template simplifies the process of making custom thickness shims for a MendelMax 2's MaxStruder extruder. The standard top holder design relies on precise building. To use different plastic shim stock thicknesses, cut them with an engraving...

The design goals were: to strengthen the assembly for safe transportation; to boost power density to approximately 0.4 watts per square centimeter; to minimize PSU load and current by using 230 volts; and be compatible with standard RepRap hardware...

... design, visit this link: http://www.thingiverse.com/thing:38749. For mounting the display to the case, you will need 4 M3x10mm screws and nuts, while for attaching the case to the MendelMax, reuse the 4 M5x10mm screws from the replaced vertex.

This Dual Bowden mount is designed for Mendelmax 1.x printers, featuring three versions: print both left and right parts or opt for the complete one, requiring side opening to slide it in. An updated split version with long extruder mount holes has...

Additional instructions are given for RAMPS v1.4, requiring two M3 15mm screws and using old MendelMax vertex's M5 10mm screws for mounting purposes. The touchscreen displayed is the 4D Systems uLCD-32PTU. A link to the original firmware is provided,...