meep from spongebob 3d models

This is based on Marlin k-factor generator with Prusa specific G-codes and settings. Naming convention for the G-code files: LA1_5-"Filament"-"Hotend temp"C-"layer height"mm-"fastest perimeter printing speed"-"Extrusion multiplier"E_mult-"Prusa...

* all protrusions from frame (filament spool, extruder, power connector) are on the right hand side to minimise desk clutter and allow the back of the BabyCube to be pushed right against a wall * Clean wiring. Include the wiring in the design,...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

The cable mechanism consists of a combination of nylon strap and metal cable running from the middle of the back to the end of the hook. It runs through the tricep guide and guide holes on the socket. The cable mechanism maintains a fixed length and...

All original models are from UntangleWORKS (https://www.printables.com/@UntangleWORKS). ...All I did was scale down the model and change the grip to fit DUMMY 13 (soozafone)(...

 The air flow direction should be pulling air from inside the enclosure to outside.Place the second TPU_Fan_Gasket_X2 on top of the fan.*Place the PETG_Fan_Exhaust_Adapter_Bracket_X1 on top of the TPU_Fan_Gasket_X2.Insert the screws that came...

The fans can be controled by the control board with a enclosure thermister (if you have enough outlets/pins on the control board). UPDATE 17/12/2021 Passive chamber temps just from the heated bed were climbing over 45°C so I have added a printable...

Until I get things sorted out, it might be easier to download from thingiverse: https://www.thingiverse.com/thing:3370714 (but I'm leaving the STLs on printables in case you want to download them here).This is a modular collection of pieces for...

There is also a strap hole, so you can use it immediately by lowering it from your neck. The device supports capacitive touch panel operation. Pass a 0.5mm steel wire through the hole at the tip and through the edge of the hole to the strap hole. If...

... the front of the box-bot parts.Lever and clip are connected with a pice of 1.75mm filament. Insert it from the right. ...(The hole on left is slightly smaller for a better fit)Optional: Add a felt inlay in the remote-top part. And… You're finished!

Important note: Feel free to ask any question related to this project in the comment section, but notice I do not own any email account with names related to this page or my youtube channel, and I don't feel comfortable opening any links from...

Please understand that I cannot regularly check links and availability and that the offers do not come from me, they are also not affiliate links, so I will not receive anything if you buy via these links. If you would like to reward my work, you can...

Base: I used some 2x4mm magnets that were left over from the MakerRx kit to hold the Base Cover to the Base. The Base can be printed without supports. I manually added a small support for the cord slot inside the Base. After printing, just pop it...

One of the screws that are used to mount the Rear Plate to the Rear Rotor Housing is in the way, so I shortened the Sparkplug Base so it would fit to the same depth as the rest of them, and glued it in. When you open the motor, be sure to remove the...

Update 08.01.2022: Added some examples for test patterns included in this model.Update 12.01.2022: Updated presliced gcode to make sure heatbed is turned on.Update 18.01.2022: Uploaded additional stl with text on test patterns describing its...

This should help keep the runout sensor from binding the filament. To assemble, a) drill out the  4mm holes in the end bracket and pivot to 4mm; b) heat up the rod and slide the pivot over it, then let it cool down and slide it back and forth...

Even Lamborghini has moved towards a more supple and luxurious look to their interiors than the past, and I believe that this is happening because of complaints from their customers about shoddy and gimmicky interiors of the past. I remember...

This is done to prevent the top and bottom from getting thicker when scaling up the model in the slicer. So if you want to print a taller/larger model you should to select the EXTRA or MEDIUM model and scale it in X/Y...

Every piece took about 6 hours to print and weighs about 50 g.Mark every piece to not lose track of already printed pieces and its position.I cut out all thediffuser panels frompaper, but you can also use the supplied diffuser file toprint them.Step...

I used small jewelers files and plenty of patience to perform this step.Assemble the Staircase.To assemble the staircase, I performed the following steps:• Slid "Staircase.stl" up through the bottom of "Base.stl", pressing it upward until the...

Update - 29/09/2020I have removed the 3D printable stand from download as keeping the clock at that high an angle does effect the sand and the strength of the movement. I will design another stand with a lower angle and see how well the clock copes.

Insert the terminals to the bottom and glue them with glue to prevent them from moving.4º Solder the positive cable of the battery connector to the positive pole of the dc-dc converter.5º Screw the dc-dc converter to the battery connector with the...

So I can consider this bay as successfully working.Print instructionsI designed this with beginners in mind. I remember how terrible it is to have to remove each support from several pieces, and then discover that they don't fit together because my...

* Adding a detachable module on top for extra Pi4 power, using supply from main unit. * Research into SLAM with pi camera and possibly LiDAR. Bill of Materials: * 18x Servos - Hiwonder LD-220MG...

I fed the wires down the vslot beams to steal 5V power from the ender board, but you may prefer to power it with a separate power supply, like a 5V or 12V adapter. I could fit 2 strips on each side, for a total of 24 LEDs, which is quite bright. It...

They're also not optimised for 3D-printing.Purchased parts:Soap dispenser (I'm using the “TACKAN” from ikea https://www.ikea.com/de/de/p/tackan-seifenspender-weiss-90322303/ )A little towel (the one i'm using is 430 x 270 mm)A canister (I'm using an...

I also redesigned the back struts so they not only prevent tipping but also allow the cables to be wrapped around them for even quicker portability. The only parts that changed from the MKII are the Base and the Handle. All other components...

Ensure all the supports have been removed from the two halves of the shell (particularly the small support underneath the overhang for the left shoulder button. To get a cleaner feel for the buttons use coarse, followed by fine, sandpaper inside...

With this converter, the fan voltage can be reduced from 12V to approx. 7-8V, so that the fans run quietly but sufficiently strong. To connect the fans to the voltage converter, I constructed a Molex adapter into which 4 standard straight 2.54mm...

Compatible with Smart Diffusers extension.Example of parameters from one family: Type CRL-400-R CRL-160-R CRL-315-R Air Flow 0.00 L/s 0.00 L/s 0.00 L/s Arrow 300.0 300.0 300.0 Arrow Distance 0.0 0.0 0.0 Arrow Length 50.0 50.0 50.0 Arrow Visible True...