meanwell power supply ender 3 3d models

This is a custom cover for the power supply of an Ender 3 printer. If you wish to upgrade to a MeanWell LRS 350 - 24v power supply, or one similar, this design will accommodate your needs. Key benefits of using this cover include: 1. Compatibility...

I replaced my Ender 3's faulty stock power supply with a Meanwell unit, which is significantly thinner than the original. Unfortunately, this means that the stock cover no longer fits properly around it. I wasn't fond of the available alternatives,...

Human: Simple Remix of Ender 3 Power Supply Fan Silencer for Ender 3 Pro Meanwell PSU. I took Eigengrow's original design, printed a few layers to check size, and flipped it since Meanwell PSU screws are oriented differently than Ender 3 PSU. Used...

I took the Ender 3 Pro Power Supply Baffler from calaverajoe, but I didn't like how thin it was, so I made it thicker

I haven't found what I've needed, so I designed this extra rigid PSU mount for Ender 3 Pro (Meanwell PSU). It slides inside 4040 extrusion with a tiny bit of force to ensure there's no wobble at all. There's a plenty of room between 4040 extrusion...

For installation need to discard the bottom cover

I upgraded Eigengrow's modified power supply silencer to ensure that the holes are precisely matched for the stock screws as shown in the image. Additionally, I adjusted the thickness of the mounting points because the stock screws were not long...

I didn't like the idea of removing screws to install a duct so I created a crude remix so magnets could be used. I used small magnets I got from Harbor Freight and they measure approximately 8mm x 2mm PN 67488. The recessed holes for the magnets...

Ender 3 Pro Power Supply Meanwell Silencer Baffler designed with 1.2mm walls thickness for extra fast print on 0.4 or 0.6 nozzles. Use existing bolts to attach it to your power supply without disassembling it (take out one screw, attach it to one...

I upgraded szkryb's MeanWell power supply model to include an extra opening for powering my control board and LED relays. Features -------- • I eliminated the 1.5mm gap at top from the original model. • I adjusted mounting holes to align better...

I used the Heavy Copper font from dafont.com/heavy-copper.font most of the He is risen logos i saw online were a bit feminine, the Gothic feel changes that a bit. Print Settings Printer Brand: Creality Printer: Ender 3 ProRafts: No Supports: ...

Instead of attaching it to my Ender 3, I chose to use it in its own right. To make this work, I sealed up the hole on the rear and flattened the bottom so that it could be used as a vertical stand. The power switch is conveniently located on one...

... with stand. > >Compatible with: Meanwell LRS-350-24 PSU HiLetGo 5V 1 Channel Relay Module With Optocoupler with High or Low Level Trigger > >Remix Sources: >PSU stand: thingiverse.com/thing:4123532 >Relay holder: thingiverse.com/thing:4186335

I replaced the power supply that came with my Geeetech A10 by a Mean Well power supply - the same power supply type used by my Creality Ender 3 Pro.I could use the bracket of the original power supply (all screw holes were at the same places) with...

<p>This is a 120mm fan mount I have designed from scratch for a 120mm fan (Specifically I had Corsair SP series 120mm PWM fans laying around).&nbsp;</p><p><strong>PRINTING DETAILS:</strong></p><p>When printing, make sure to combine “Fan filter...

Since i was 3d printing this, thought i'd through a cross and He is risen on it. came out well. ...I used the Heavy Copper font from dafont.com/heavy-copper.font most of the He is risen logos i saw online were a bit feminine, the Gothic feel changes...

PSU COVER BOX WITH TOOL HOLDER MEANWELL COVERS POWER SUPPLY ENDER 3/PRO

After upgrading my Ender 5 Plus board to an BTT SKR Pro V1.2 board, my power supply needed to shift positions a little bit. Designed this bracket to allow for several positions. The 4mm holes are 3.3mm for tapping or just thread the screws into...

Ender 3 V2 drawer replacement for Raspberry Pi with Meanwell Power Supply Space for MEANWELL original RS-15-5 5V 3A Single Output Switching Power Supply AC-DC (I first used a DC/DC converter but it brunbed up so I decides to use an extra Power Supply...

Mounts for Meanwell power supplies, designed for LRS-350

Mount for a single Meanwell power supply. ... Elevated to enable wiring to run underneath.

Also: The Original Ender 3 uses a thicker power supply, this remix won't fit! ... Take a look at my other projects/things: Ender 5 dual z axis mod: https://www.thingiverse.com/thing:4079052 Raspberry Pi camera night vision case:...

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...

PSU Cover for Meanwell RS-75-24 Currently using as a second supply for a custom printer build. Fits supply exactly. Printed in PETG with 20% infill / 3 perimeters / 5Top/5Bottom Layers. ... Category: 3D Printer Parts

PSU Cover for Meanwell RS-75-24 Utilizing it as a redundant power source for a customized printer project. Provides an exact fit for the supply. ...Printed using PETG material with a 20% infill density, three perimeter walls, and five layers on top and...

When hanging the power supply, the powerplug "hanging" did not work for me,

A straightforward protective case for individuals hesitant to face electrical shock when powering up or down their printers. ...Engineered specifically for the LRS-350 power supply units.

Parts list so far: Various 4mm screws (6mm countersunk are ideal for mounting the PSU, and ~10-12mm are good for the powerpole mount) Delta SK-015A Cherry LRA22H2BBRLN 16AWG wiring of various colors Powerpoles and connectors Errata I needed more...

The source model has tapered head screws to mount to the underside of the power supply. I modified this to support socket head cap screws instead. There are 2 models included. One will require supports for decent printing where the socket head...

I shifted the power supply on my Ender 3 Pro to prevent the mat from collapsing.