meanwell ender 3 3d models

Remix Soporte con perfil aligerado para colocar NOCTUA 60x25 externo en al Meanwell original mas rapida impresión, facilidad de colocación externa del ventilador con carcasa original del PSU.Impresion con iguales caracteristicas que el...

PSU COVER BOX WITH TOOL HOLDER MEANWELL COVERS POWER SUPPLY ENDER 3/PRO

Upgraded the power supply on my Ender 3 to the Meanwell unit and added an automotive style voltmeter/USB combo.

Remix of https://www.thingiverse.com/thing:3484372 by charlatan154 This fits on non Meanwell/Standard PSU as well, I made to suit 25mm Noctua fan on my Ender 5. ... Note if putting on Ender 5 you will need to cut bottom plate and raise whole printer up...

Offset for Ender 3 PRO PSU to accommodate dual Z stepper Print : 0.2 height 4 walls 40% infill This should fit like a glove, unless your printer is really badly calibrated. The screw recess is 2mm deep, in some cases the original set of screws may...

I bought the Meanwell PSU for my Ender extender kit for non-pro. Found that i needed to modify it to fit on the end. This is for the non-pro version with the aluminum extrusion screwed into the top holes. ...I can modify if anyone is interested in...

My machine is Ender 3 (non-Pro) with Meanwell PSU (bought separately). I use this PSU relocation mod for my Ender 3. Highly recommended. https://www.thingiverse.com/thing:4101358 Tested for Ender 3 Pro. Please share your makes so I know this is...

Meanwell Power Supply Controlled Creality Ender 3 Pro Tool Holder System.

This is a replacement PSU mount/cover/bracket for the Ender 3 Pro's MeanWell power supply. # Features * Moves the AC power connector to the back * Has a mounting point for an inexpensive 5V relay board, which can only handle 10A and must switch on...

And as I wanted to replace the old PSU with the LRS-350-24 PSU from Meanwell, this asked for a redesign (o;It is advisable to have a protective ground cable attached to the PSU and the back of the profile as the supplied mounting angle for the PSU...

One more note: The Meanwell PSU's fan seems to blow down, into the PSU, towards the circuitry and out where the wire connections are made/the bottom. ...I flipped the fan so it sucks through the bottom instead and blows out the hole as it seems to have...

Modified cover designed specifically for larger MeanWell NES-350 power supplies, ideal for use with the Creality Ender-3 3D printer and suitable for any application requiring a power supply of similar dimensions.

I upgraded my stock Ender 3 power supply after it failed multiple times, replacing it with the Meanwell power supply from the Ender 3 Pro and taking advantage of the opportunity to reposition the switch to the back of the printer. As seen in...

The stock Ender 3 power supply's failed several times on me, so i changed it to the Meanwell power supply from the Ender 3 Pro and took the chance to also relocate the switch to the back of the printer.As maybe seen in 'Thingiview' or in your Slicer,...

Here's a little upgrade for the Ender-3. I recently decided to replace the original power supply with a high-quality one from Meanwell because it didn't meet my standards. Alongside this, I've installed a USB supply that was sourced from the car...

This is a Meanwell 350-24 PSU stand for an Ender 3 V2. The power supply was not getting as much air as I think it should tucked away under the printer. This is a stand-alone option and I used some 200'C silicone 16 gauge wire to connect the PSU to...

I replaced my Ender 3's faulty stock power supply with a Meanwell unit, which is significantly thinner than the original. Unfortunately, this means that the stock cover no longer fits properly around it. I wasn't fond of the available alternatives,...

Redesigned specifically for the Creality Ender 3, this adaptation seamlessly fits the PSU width while eliminating the unnecessary hole on the right side.

This is a redesigned PSU mount for the Meanwell LRS 350-24v. I found the original design on this platform but couldn't locate it to post an updated version. Hopefully, this revised model meets expectations. I don't use mesh modeling software, only...

When I replaced my default power supply with the meanwell LRS 350, the holder for the power supply had a gap that needed filling. I didn't want to re-print the whole shroud, so this spacer screws into the hole that the old power supply used. I put a...

When I replaced my default power supply with the meanwell LRS 350, the holder for the power supply had a gap that needed filling. I didn't want to re-print the whole shroud, so this spacer screws into the hole that the old power supply used. I put a...

I replaced my default power supply with the meanwell LRS 350, but the new unit left a gap that needed to be closed. I didn't want to reprint the entire shroud, so I came up with this spacer solution. The spacer screws into the hole where the old...

Original version of this was too narrow for my plug. Widened the plug base to allow for that back of plug wiring to fit. ...

A custom fan cover is designed to fit the Ender 3 Pro's Meanwell PSU, with an optional filter for added functionality. The new setup effectively muffles the fan's noise, achieving a reasonable level of silence. ...Its installation was prompted by the...

make your ender 3 pro silent use a standard meanwell power supply uhp-350-24 with no fan use my brackets - easy to mount just slide into the Aluminium profile and fix it with 4 screws additionally no changes in the electrics necessary, use the...

A Remix of Munchingfoos Meanwell LRS 350 Mount as to fit with PSU Cover for 92 mm Fan (Thing 4140152).

... is only for the Meanwell PSU from the Pro version, the older PSU is about 50mm width and will not fit! Fits all tools from Ender 3 3 tweezers 6 nozzles The holder for the clipper is the only part which needs support (my support fell over :( )

... as the older model is approximately 50mm in width and will not fit. + Accommodates all tools from Ender 3 + Includes 3 tweezers + Features 6 nozzles A tower has been added to deactivate supports. ...Additionally, the original mesh has been fixed.

This is a remix from https://www.thingiverse.com/thing:3023240 to fit the Ender 3 Pro/Meanwell power supply which has only one screw at the back. It uses the original screw (if you want to). No supports needed (if printed with 0.2 layer height or...

The Meanwell LRS-250-24 power supply on the Ender 3 Pro has a loud fan which works intermittently. This is an adapter for a standard 92mm PC case fan. Mounting screws required are the 4 self-tapping screws supplied with the case fan and the 2 screws...