meade xt90 3d models

See also: [Meade DS-90 Tripod Clip-On Battery Box](https://www.thingiverse.com/thing:5503388) Like my earlier parts, this clips to the Meade DS-90 EC tripod legs, but on the outer side of the leg. ...Included is a dust-cap holder, an observation...

See also: Meade DS-90 Tripod Clip-On Battery Box (https://www.thingiverse.com/thing:5503388) Like my earlier parts, this clips to the Meade DS-90 EC tripod legs, but on the outer side of the leg. ...Included is a dust-cap holder, an observation notebook...

See also: [Meade DS-90 Tripod Clip-On Battery Box](https://www.thingiverse.com/thing:5503388) Like my earlier parts, this clips to the Meade DS-90 EC tripod legs, but on the outer side of the leg. ...Included is a dust-cap holder, an observation...

These two gearboxes having different backfocus (105mm for Celestron and 86mm for Meade), this adapter is available in 4 versions :1> rdf Celestron + Asi Bf 12.5mm 2> rdf Celestron + Asi Bf 17.5 mm 3> rdf Meade + Asi Bf 12.5mm 4> rdf Meade + Asi Bf...

These two reducers have different backfocus values: 105mm for Celestron and 86mm for Meade, resulting in four versions of the adapter: 1) rdf Celestron + Asi Bf 12.5mm, 2) rdf Celestron + Asi Bf 17.5 mm, 3) rdf Meade + Asi Bf 12.5mm, and 4) rdf Meade...

I'm happy to share a 3D printable "light pollution Shielding Cap" for Meade DSI I/II/III telescopes, which effectively blocks light pollution from reaching the CCD sensor. If you're interested in trying it out, you can also download STL files from my...

1 - Adapter 1 replaces the Meade eyepiece holder to let you connect 1 1/4” eyepieces to the (approximately) 2 3/8” focuser tube. Print 1A Focuser Attachment with the flange down, threads up. Print 1B Eyepiece Holder *or* 1B Eyepiece Holder Short...

# MEADE LX200 Telescope GOTO Hand Controller Repair / Rebuilt Please also have a look on my GitHub: https://github.com/Spo-ck/MEADE-LX200-Telescope-GOTO-Hand-Controller-Repair-Capacitor-Kondensator-Issue-solved # Capacitor / Kondensator Issue solved...

These were some parts I needed to replace while fixing up an old Meade DS-90 EC reflector telescope. The tripod for these scopes were notorious for having bad clamps that don't hold their extension at all. I've seen various ways of repairing these,...

These were some parts I needed to replace while fixing up an old Meade DS-90 EC reflector telescope. The tripod for these scopes were notorious for having bad clamps that don't hold their extension at all. I've seen various ways of repairing these,...

These were some parts I needed to replace while fixing up an old Meade DS-90 EC reflector telescope. The tripod for these scopes were notorious for having bad clamps that don't hold their extension at all. I've seen various ways of repairing these,...

Remove the .965" adapter and screw this into the focus tube to use 1.25" eyepieces.

As the Title Clearly States

Designed to be printed in TPU so it's a snug fit, If you print in anything other than TPU then you should probably scale it up 1-2% It should be flipped over so the embossed side prints face down on the bed. ... There is a little lip around the...

BEFORE YOU PRINT: 1. Only the ring needs support, specifically for the dovetail overhang; refer to pictures for optimal print orientation. 2. I had to enlarge the original Arca-Swiss clamp design because it was too small for my Canon mount; I'm...

DIY Spacer/adapter for ETX-80 Objective Cell and Baffle Assembly Fits 4" OD, 3-7/8" ID Carbon Fiber Tube Securely Attach to Front End of Tube Using Epoxy Trim Ring Made from Aluminum Presses Over Cell and Spacer Allows Use of Factory Dust Cover and...

You'll Need an Arcaswiss Camera Mount for Your Telescope That Accommodates a 1.25-Inch Eyepiece. ... To Get Started, You Will Require the Following Items: One M6 x 60 Bolt One M6 Nut Two Steel Springs from Ballpoint Pens

Customized version of https://www.thingiverse.com/thing:266400 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=266400

Some printers are quite cramped.

Here is a continuation of my screw on dew shields for the ETX line of scopes. This one was a request for a ETX-125 version. This is for the original ETX-125 not the new ETX Observer. You can flip this around and it will fit over the scope for...

This knob slides onto the existing focus knob of the LX-90 allowing finer focus adjustment due to having a larger diameter. It may be a little tight so just sand the hole slightly for a tight friction fit. ... I printed mine with PLA but can also use...

A Replacement Focus Knob, in case you've misplaced yours. To install it, gently strike the side hole with a 4-millimeter punch to loosen a grub screw. ...If the shaft hole appears too tight, carefully insert a thin drill bit and run it down to the base...

This adapter is specifically designed to securely hold a 50mm tube from the LXD75 telescope mount.

Customized version of https://www.thingiverse.com/thing:266400 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=266400

Had to fabricate a rear port cap for my ETX-60 telescope. Threads are reportedly 1-3/8 at 22 threads per inch, and the iso tap tool in Tinkered came remarkably close, allowing the part to thread all the way first time. This is only 1 millimeter...

Cutting and re-soldering wires along with drilling a small hole into your plastic ETX base is an absolute must. First off, print the box on its side using tree support - you'll need to enable experimental settings in Cura for this. ... Next up, print...