meade xt90 3d models

To transport the secondary onto the primary, I drew these clips to H.

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. Print Settings Supports: No Resolution: 0.2 Infill: 5 Notes: Infill 5% to allow it to flex a little bit, 0% also works. ... Wall count 3 ...

Customized version of https://www.thingiverse.com/thing:3968935 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3968935

This holder is an evolved version of Nicolas_T's original design, adapted to a sturdy round tripod base. My custom tripod boasts a clever convolute extrusion that initially struggled to accommodate the round clamp. Fortunately, Nicolas_T's innovative...

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

This holder is a remix originally from Nicolas_T . The original design clamped to a round tripod base. My tripod uses a convolute extrusion that the round clamp didn't fit very well. His holder worked perfectly so I incorporated it into my...

Rapid Eyepiece Mount for ETX-80 in OpenSCAD, easily fits either tapped screws or a glued nut. Editable comments at the top can be modified in OpenSCAD or hopefully Customizer if necessary. Printed upside down, minimal support needed. ...Thumbnail image...

A personalized version of http://www.thingiverse.com/thing:56910 has been created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=56910. ...To achieve this, parameters were set as follows: part gap of 0.08mm, lip height...

Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391 Instructions Using the following options: gap = 4...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. ...

I'm looking for a Bahtinov mask made specifically for my 50mm finder scope. It needs to be of high quality and provide accurate results. ...Can you recommend one that fits this description?

This innovative control enables users to capture images while blocking unwanted light from reaching the camera, eliminating the need for manual lens caps during daytime shots, as well as allowing them to take low-light photos without covering the...

I recently acquired an ETX-90 with a computer-controlled mount that presented some challenges. The DEC clutch was slipping, a common issue, and I joined the ranks of those who broke the knurled nut loose on the clutch peg. This is my approach to...

Just heat it up slightly with some warm air or a blowtorch.

Suggest printing with 25-30% infill. Added raft and support, print with the round side down for the circular cutout section to keep supports removable and avoid perpendicular holes connections. Use with 8-32in bolt between 2.5-3in, suggested with...

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.

3D printable "light pollution Shielding Cap" for Meade DSI I/II/III pro with color filter version,which can completely shield light pollution onto CCD sensor.

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.

This is a replacement for broken Meade DS 60 telescope focuser rack. Maybe it will fit to other telescope rack and pinion focuser models. ...See dimensions on pictures.  Resolution:0.1 mmInfill: 20%

This is the Meade ds-60 telescope rack and pinion focuser replacement part for rack. I cut area with broken teeth and glued printed part. Maybe it will fit to other focuser models. ...See dimensions on pictures.

Voici la vis de blocage de l'embrayage de la lunette Meade ETX-70 ETX 70 Impression en 0.1mm remplissage a 100%. ... A imprimer de préférence avec du PETG ou de l'ABS