meade lx075 3d models

Over the years, excessive moisture and heat have taken their toll on my Meade Plossl eyepieces' rubber eyecups. I resolved to create my own replacements using a flexible filament. This endeavor proved successful, and I've upgraded dozens of eyepieces...

This collection includes the essential components you'll need to convert the 2" focuser on your Meade 4504 telescope (or similar model) from 0.965" eyepieces to 1.25" eyepieces. The package contains: * A 1.25" focuser stop, which securely attaches...

... in symmetrical patterns. Designed specifically for Meade ETX-125 OTA with 127 mm (5") clear aperture, 1900 mm focal length (f/15), and 148 mm OD, this 3D-printed Bahtinov focusing mask is constructed from black ABS filament on a delta printer.

### Notable Autostar configuration parameters Telescope - 4504/114EQ if FW patched, otherwise DS-127 Alt/Dec Ratio = -03.28533 (1:144 worm ratio) Az/RA Ratio = +03.28533 (1:144 worm ratio) Alt/Dec Percent = 75% Az/RA Percent = 75% ### Parts list 2x...

The focuser on my Meade LX200 10" telescope is a bit too coarse for me when using higher power eyepieces. I had planned to make one from a ball style reducer but couldn't find an inexpensive one suitable for the project. Then, I came across the...

I have modified all of the parts in Fusion 360 to fit the geometry of the Meade LX90 8inch SCT and possibly other Meade SCTs depending on the Focus Knob used. The EAF positioning allows adjustment and removal of the EAF for transport and avoids...

At the last minute I made up my mind to purchase a solar filter for my Meade ETX-60. I came up with a design for a lens cover and then modified it by adding an ISO threaded 0.75 pitch 62 mm hole (which printed best at 63.4 mm, so with shrinkage the...

Just heat it up slightly with some warm air or a blowtorch.

This innovative control enables users to capture images while blocking unwanted light from reaching the camera, eliminating the need for manual lens caps during daytime shots, as well as allowing them to take low-light photos without covering the...

To transport the secondary onto the primary, I drew these clips to H.

I recently acquired an ETX-90 with a computer-controlled mount that presented some challenges. The DEC clutch was slipping, a common issue, and I joined the ranks of those who broke the knurled nut loose on the clutch peg. This is my approach to...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. ...

I'm looking for a Bahtinov mask made specifically for my 50mm finder scope. It needs to be of high quality and provide accurate results. ...Can you recommend one that fits this description?

This holder is an evolved version of Nicolas_T's original design, adapted to a sturdy round tripod base. My custom tripod boasts a clever convolute extrusion that initially struggled to accommodate the round clamp. Fortunately, Nicolas_T's innovative...

Rapid Eyepiece Mount for ETX-80 in OpenSCAD, easily fits either tapped screws or a glued nut. Editable comments at the top can be modified in OpenSCAD or hopefully Customizer if necessary. Printed upside down, minimal support needed. ...Thumbnail image...

Suggest printing with 25-30% infill. Added raft and support, print with the round side down for the circular cutout section to keep supports removable and avoid perpendicular holes connections. Use with 8-32in bolt between 2.5-3in, suggested with...

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391 Instructions Using the following options: gap = 4...

This holder is a remix originally from Nicolas_T . The original design clamped to a round tripod base. My tripod uses a convolute extrusion that the round clamp didn't fit very well. His holder worked perfectly so I incorporated it into my...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. Print Settings Supports: No Resolution: 0.2 Infill: 5 Notes: Infill 5% to allow it to flex a little bit, 0% also works. ... Wall count 3 ...

Customized version of https://www.thingiverse.com/thing:3968935 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3968935

A personalized version of http://www.thingiverse.com/thing:56910 has been created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=56910. ...To achieve this, parameters were set as follows: part gap of 0.08mm, lip height...