meade lnt module 3d models

full fan module (40x40x6.5mm). custom brims made for easy removal .when printing supports are not needed for fan blades and cover. when assembling, place motor in dedicated slot in the main body making sure that the wires pass through the slit made...

I'm looking for a Bahtinov mask made specifically for my 50mm finder scope. It needs to be of high quality and provide accurate results. ...Can you recommend one that fits this description?

Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391 Instructions Using the following options: gap = 4...

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

This holder is an evolved version of Nicolas_T's original design, adapted to a sturdy round tripod base. My custom tripod boasts a clever convolute extrusion that initially struggled to accommodate the round clamp. Fortunately, Nicolas_T's innovative...

This holder is a remix originally from Nicolas_T . The original design clamped to a round tripod base. My tripod uses a convolute extrusion that the round clamp didn't fit very well. His holder worked perfectly so I incorporated it into my...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. ...

A personalized version of http://www.thingiverse.com/thing:56910 has been created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=56910. ...To achieve this, parameters were set as follows: part gap of 0.08mm, lip height...

I recently acquired an ETX-90 with a computer-controlled mount that presented some challenges. The DEC clutch was slipping, a common issue, and I joined the ranks of those who broke the knurled nut loose on the clutch peg. This is my approach to...

This innovative control enables users to capture images while blocking unwanted light from reaching the camera, eliminating the need for manual lens caps during daytime shots, as well as allowing them to take low-light photos without covering the...

Customized version of https://www.thingiverse.com/thing:3968935 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3968935

Suggest printing with 25-30% infill. Added raft and support, print with the round side down for the circular cutout section to keep supports removable and avoid perpendicular holes connections. Use with 8-32in bolt between 2.5-3in, suggested with...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. Print Settings Supports: No Resolution: 0.2 Infill: 5 Notes: Infill 5% to allow it to flex a little bit, 0% also works. ... Wall count 3 ...

Just heat it up slightly with some warm air or a blowtorch.

Rapid Eyepiece Mount for ETX-80 in OpenSCAD, easily fits either tapped screws or a glued nut. Editable comments at the top can be modified in OpenSCAD or hopefully Customizer if necessary. Printed upside down, minimal support needed. ...Thumbnail image...

To transport the secondary onto the primary, I drew these clips to H.

Module

Support for outdoor module of Netatmo weather station. Small holes enable airflow, while a water evacuation system ensures excess moisture escapes. A protective lid shields the module from rain. ...Printer Settings Printer: Dagoma Discovery 200

High-Speed Micro-Stepping Servo Motor Driver Card Kit Module System Controller Circuit Board Platform Development Solution

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.