meade etx autostar manual 3d models

Solar/Lunar filter attachment for a Meade ETX-70 telescope. An absolute must for viewing a solar eclipse! Includes a built-in indirect sight for aiming. Use with solar film such as this for solar viewing. Print with ABS to handle the sun's heat...

I'm thrilled to be the proud owner of a Meade ETX-70 telescope, a trusted companion that's stood by me through countless nights of stargazing. However, after 10 years of faithful service, the knobs that control the declination of my optics have...

This is the holder for Meade ETX 125 Focus Control, firmly secured on a tripod with the aid of a tray. Simply screw it in and it will function perfectly. Unfortunately, no support was generated for a 3D print. However, pictures of my printed...

I wanted to connect my RPi Camera to the back of my Meade ETX 90 but found that nothing existed. Taking some design cues from other designs (the M12 mount - http://www.thingiverse.com/thing:539517, Adapter ring -...

_______________ This is my Fine Focuser for the Meade ETX-60 and 70. The stock focus knob is hard to reach and turn. To I made this to extend the knob out the back of the ETX OTA. The design uses the existing knob which is inserted in the base....

Note: The ETX-125 has much finer threads on the objecting lens that the other ETX scopes I have done (60, 70, 80). There is no way a FDM printer can print these reliably. Thus I "doubled" the threads. It works as it's plastic but you need to be...

DIY Spacer/adapter for ETX-80 Objective Cell and Baffle Assembly Fits 4" OD, 3-7/8" ID Carbon Fiber Tube Securely Attach to Front End of Tube Using Epoxy Trim Ring Made from Aluminum Presses Over Cell and Spacer Allows Use of Factory Dust Cover and...

Cutting and re-soldering wires along with drilling a small hole into your plastic ETX base is an absolute must. First off, print the box on its side using tree support - you'll need to enable experimental settings in Cura for this. ... Next up, print...

... every session. ...Cap slips on the Meade plastic dew shield with just enough friction. It's thick enough for astrophotographers to use for capturing dark frames. Customized version of https://www.thingiverse.com/thing:4130861Created with Customizer!

Location is the straight-through rear port underneath the eyepiece on the ETX-60. Alternative options include remixing with increased thickness to the base, adding a 38-millimeter disk to the bottom for any desired thickness and adjusting your fill...

Hello, I bought a 2nd hand Meade Telescope with a DS goto mount, the Azimuth was not working, just grinding initially, then worse. Two gears were bad, the 42T gear that drives the worm gear and the 30T12T gear that drives that. Also both the...

Excellent, sturdy bracket for mounting a red-dot sight on your Meade ETX-80 refractor telescope. ...Adding a sight greatly assists in alignment, either manually or for automatic object location.

JUST HAVE TO CUT THE NOTCH WITH CLIPPERS. ...

Here is a remix of wt808's Meade focuser support. ... This one is for older Meade ETX-80 telescopes. This will need internal supports but they are easily removed as they are small. ... Enjoy, Bob

Meade ETX-125 Red dot finder Dovetail Mount This bracket, designed specifically for the Meade ETX-125, allows me to easily install a standard dovetail finder on my telescope. ... Replacing the existing angle finder bracket, this mount utilizes the same...

The Meade ETX telescope's rear port is converted to accommodate an accessory with a T/T2 (M42x0.75) female thread, requiring a 1-3/8"-24tpi male adapter.

3D printed base that sticks onto the bottom of the ETX-125 with double sided tape for use with the Meade 884 field tripod. The 884 tripod only has two attachment screws to hold the ETX-125, which is a slightly heavy telescope. The issue is it can...

Voici la vis de blocage de l'embrayage de la lunette Meade ETX-70 ETX 70 Impression en 0.1mm remplissage a 100%. ... A imprimer de préférence avec du PETG ou de l'ABS

... in symmetrical patterns. Designed specifically for Meade ETX-125 OTA with 127 mm (5") clear aperture, 1900 mm focal length (f/15), and 148 mm OD, this 3D-printed Bahtinov focusing mask is constructed from black ABS filament on a delta printer.

After many hours of drawing, tweaking and screwing up, here is the famous stand that can save your Meade ETX-70 telescope... This part is unobtainable on the market, even from the manufacturer. ... All you will have to do is print it in PLA or ABS...

This kit includes everything you need to mount a camera to the Meade ETX 70AT telescope for long exposure photography using the Meade ETX 70AT's motorized mount and a PH 249Q gimbal. To attach the PH 249Q_Palanca.stl gimbal to the CLAMP_2.stl epoxy...

At the last minute I made up my mind to purchase a solar filter for my Meade ETX-60. I came up with a design for a lens cover and then modified it by adding an ISO threaded 0.75 pitch 62 mm hole (which printed best at 63.4 mm, so with shrinkage the...

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.

This is a more solid holder controller for the Meade Autostar and Audiostar controllers, specifically to clip onto the tripod legs of the DS-90 EC.

I did an ETX-80 Dew shield and decided to make one for the ETX-60 and 70. This is a screw on dew shield and you can flip it over the OTA doe storage. ... Set your slicer for 8 walls so the threads are strong with no infill.

This version includes for a 2° inclined orientation of the LNT mount, since after printing the original file for my ETX-125PE, I could not "twiddle in" vertically with the red dot on target (at maximum adjustment, it was still below the target), but...

A clever hack allows users to repurpose the alt-az mount of the ETX to pivot towards Polaris, effectively converting it into an equatorial mount. This innovative solution enables a single motor to counterbalance Earth's rotation, resulting in...

You'll Need an Arcaswiss Camera Mount for Your Telescope That Accommodates a 1.25-Inch Eyepiece. ... To Get Started, You Will Require the Following Items: One M6 x 60 Bolt One M6 Nut Two Steel Springs from Ballpoint Pens

This adapter is specifically designed to securely hold a 50mm tube from the LXD75 telescope mount.