meade etx 125 replacement parts 3d models
672804 3d models found related to meade etx 125 replacement parts.thingiverse
Meade ETX-125 Red Dot Finder Mount This is a bracket of my devising allowing me to install a red dot finder on the Meade ETX-125. Replaces the existing angle finder bracket and uses the same screw for mounting. ... Thanks for looking.
thingiverse
... mount. Additional fasteners are needed if using the mount for an aluminum dovetail base. Drill and tap holes as needed. You can read more about installing the Meade LNT on an ETX-125 here: http://www.weasner.com/etx/techtips/2007/lnt-add-on.html
thingiverse
This is holder for Meade ETX 125 Focus Control, Fixes on Tripod with help of tray. Just Screw and it will work No Support generated for 3D print Pictures of my print, which is working fine. ... STL is further improved after my print, like...
thingiverse
A bracket for mounting a Meade 1244 electric motorized focuser kit on a Meade ETX-125 telescope. The 1247 kit for the ETX-125 is difficult to find and the 1244 kit for the ETX-90/105 is more-readily available. No drilling or permanent...
thingiverse
Note: The ETX-125 has much finer threads on the objecting lens that the other ETX scopes I have done (60, 70, 80). There is no way a FDM printer can print these reliably. Thus I "doubled" the threads. It works as it's plastic but you need to be...
thingiverse
A focus Knob, incase you have lost one. You will need to tap the side hole with a 4mm tap to take a grub screw. ...if the shaft hole is a bit narrow try running a small drill down to the bottom.
thingiverse
This is a telescope ring to mount a viewfinder on Meade ETX-125 telescopes. It fits under the forks so you can adjust it far back on the tube. I designed it to work with the dovetail mount linked below. I designed this in inches so you may have to...
thingiverse
Meade ETX-125 Red dot finder Dovetail Mount This is a bracket of my devising allowing me to install a standard dovetail finder on the Meade ETX-125. Replaces the existing angle finder bracket and uses the same screw for mounting. ... Thanks for...
thingiverse
The gears fit perfectly (first go!) (meshing and onto shaft) for me, the 42T on the worm gear shaft I pressed fit onto the spines without glue, I made the part that goes over the shaft spline thicker for strength. For the motor mount repair, I...
thingiverse
3D printed base that sticks onto the bottom of the ETX-125 with double sided tape for use with the Meade 884 field tripod. The 884 tripod only has two attachment screws to hold the ETX-125, which is a slightly heavy telescope. The issue is it can...
thingiverse
... becomes symmetrical. The 3D-printed bahtinov focusing mask is designed to fit Meade ETX-125 OTA with 127 mm (5") clear aperture, 1900 mm focal length (f/15). and 148 mm OD. ... The mask is printed from black ABS filament on a delta printer.
thingiverse
The Meade ETX series LNT module mount is the BANE of this series of telescopes, since it is thin plastic that become brittle and disintegrates over time. Furthermore, the case (if you bought one) is likely to break it if time has not. This PLA...
thingiverse
Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
Suggest printing with 25-30% infill. Added raft and support, print with the round side down for the circular cutout section to keep supports removable and avoid perpendicular holes connections. Use with 8-32in bolt between 2.5-3in, suggested with...
cults3d
After many hours of drawing, tweaking and screwing up, here is the famous stand that can save your Meade ETX-70 telescope... This part is unobtainable on the market, even from the manufacturer. ... All you will have to do is print it in PLA or ABS...
thingiverse
I lost the battery door for my Meade ETX-60 so decided to CAD one up. This works perfectly. It also works on the ETX-70 and ETX-80. You only need supports under the back hinge tabs. I used custom supports in Cura and added then only there. ... You...
thingiverse
Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
Customized version of https://www.thingiverse.com/thing:160391 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=160391
thingiverse
Easy on and off holder for a laser pointer. Inherently aligned with the tube, no set screw adjustments to fiddle with. Simply attach to the telescope using a pair of sewn elastic straps. Laser pointer model is no-name green light tactical model...
thingiverse
This is a Bahtinov mask for the Meade ETX-90. ...It was designed for the 90mm clear aperture and 1250mm focal length of the ETX-90.
thingiverse
Meade ETX #884 field tripod bracket that has a cutout for the Talentcell 3000mah battery and an Autostar holder bracket.
thingiverse
This part should also be compatible with the Meade ETX-60AT. This was designed for the repair of a telescope that was dropped, shattering the eyepiece holder and secondary "flip-up" mirror. The plastic of the original telescope is ABS. You may...
thingiverse
A series of mounts and adapters for counterbalancing a Meade ETX telescope in its fork mount. Proper counterbalancing should result in less tension required on the clutch locks and hopefully, longer life for clutch components and gears. First is...
thingiverse
Made a much stronger Meade ETX RA Lock Lever. This can be printed in PLA and is plenty strong. Print with 10 walls to eliminate as much infill as possible. This is what gives it it's strength. ...
thingiverse
I wanted a Bahtinov mask for my Meade ETX80 and couldn't find one that was the right size. This mask fits over the dew shield but is a bit snug. ...I used the online Bahtinov generator (https://satakagi.github.io/tribahtinovWebApps/Bahtinov.html) to...
thingiverse
I recently acquired a ETX-90 with a computer controlled mount. I had some problems withe the DEC clutch slipping and like everyone else broke the knurled nut loose on the clutch peg. This is my take on a repair for this model of mount. I had the...
cults3d
Replaces the hinge that articulates the horizontal motor of a Meade ETX-70 with the stand.
thingiverse
Thanks to wt808 for the original design. I was not able to make it stay on reliably with the original design. Updated design adds a screw mount to the housing (you need to provide a screw approx. twice as long as the original). I also added a place...