meade autostar models

... the bolt holes to a diameter of 3.175mm and added a generous counter bore of 6.35mm for smooth screw threading into the leg. Now everything assembles seamlessly with my telescope. Thanks for designing such an excellent model for me to build from!

The model may require some minor sanding adjustments before assembly. ...To ensure its structural integrity, I printed the design at 25% infill; however, you can likely get away with printing it at a lower infill density of 12% without compromising its...

This is a very amateur but workable model that needs a little post-printing refinement. Please see the Post-Printing tab. **UPDATE June 3, 2023 11:52am** No changes to the design, but I did use it complete the cementing. Rather than use it right...

This custom-built adapter was created using precise measurements from my own 56mm EP, so its compatibility may vary based on the size of your eyepiece – especially if yours isn't a standard 56mm model. ... 12/16/17 I made some adjustments to the...

Just heat it up slightly with some warm air or a blowtorch.

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. Print Settings Supports: No Resolution: 0.2 Infill: 5 Notes: Infill 5% to allow it to flex a little bit, 0% also works. ... Wall count 3 ...

Customized version of http://www.thingiverse.com/thing:160391 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=160391 Instructions Using the following options: gap = 4...

To transport the secondary onto the primary, I drew these clips to H.

This innovative control enables users to capture images while blocking unwanted light from reaching the camera, eliminating the need for manual lens caps during daytime shots, as well as allowing them to take low-light photos without covering the...

This holder is a remix originally from Nicolas_T . The original design clamped to a round tripod base. My tripod uses a convolute extrusion that the round clamp didn't fit very well. His holder worked perfectly so I incorporated it into my...

Rapid Eyepiece Mount for ETX-80 in OpenSCAD, easily fits either tapped screws or a glued nut. Editable comments at the top can be modified in OpenSCAD or hopefully Customizer if necessary. Printed upside down, minimal support needed. ...Thumbnail image...

I'm looking for a Bahtinov mask made specifically for my 50mm finder scope. It needs to be of high quality and provide accurate results. ...Can you recommend one that fits this description?

Suggest printing with 25-30% infill. Added raft and support, print with the round side down for the circular cutout section to keep supports removable and avoid perpendicular holes connections. Use with 8-32in bolt between 2.5-3in, suggested with...

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

A personalized version of http://www.thingiverse.com/thing:56910 has been created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=56910. ...To achieve this, parameters were set as follows: part gap of 0.08mm, lip height...

Handbox for my LX200R, should work for any LX200 (or even LX400) with fork arm handle. ...

This holder is an evolved version of Nicolas_T's original design, adapted to a sturdy round tripod base. My custom tripod boasts a clever convolute extrusion that initially struggled to accommodate the round clamp. Fortunately, Nicolas_T's innovative...

Customized version of https://www.thingiverse.com/thing:3968935 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3968935

This is the Meade ds-60 telescope rack and pinion focuser replacement part for rack. I cut area with broken teeth and glued printed part. Maybe it will fit to other focuser models. ...See dimensions on pictures.

This is a replacement for broken Meade DS 60 telescope focuser rack. Maybe it will fit to other telescope rack and pinion focuser models. ...See dimensions on pictures.  Resolution:0.1 mmInfill: 20%

A set of two adapters for Meade reflecting telescopes such as DS-114AT and related models. The standard eyepieces that come with low-end Meade telescopes are 0.965” diameter. Higher quality eyepieces are available but the tube diameter is 1 1/4”...