mcqueen 3d model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_width = 100 use_mouse_ears = 1 pattern_element_overlap = 51 stencil_shape = 4 custom_back_camera_y_size = 20...

Creality slicer use edit, multiply selected models. PrusaSlicer use cut and past. I'm sure it's possible in other slicing software too. I would recommend printing a few extra as you may damage the edge on a few when inserting them. Assembly: ...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

My printer is a I3 Pro Dual Extruder, so I know for sure it fits that model and probably all of the I3s that were made with that frame. Update 1/22/18: I added a new mounting plate that moves the stepper motor forward. This allows the X carriage to...

A perfect fit for your specifications, this model features the following options: picture =...

It may also have fitment issues with non-TM branded or aftermarket upgraded models. Please read the Print Settings section for details. ==CONCEPT== The JTW HCC-2A is the evolution of the Hi-CAPA Carbine Version 1...

It was just hard to get some of the screws in it so I had to manually remove the parts this model has removed for you. Make sure is you use screws to hold the bearings tight that the lowest ones have low profile heads or they will be lower than the...

This stage can be handled in several ways: 1: The instructor can have several models pre-made for demonstration and discussion. 2: The instructor can have kits of parts put together for students to work with and attempt to build their own trusses. 3:...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

This project is intended for use with circular lenses that are delivered in glasses ordered from Zenni Optical with this particular frame: https://www.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500 For either model of Quest,...

The model can accommodate slightly larger and smaller sizes as is. To fit your doorknob you may either scale the STL file before printing (measure your doorknob diameter D and scale by D/54), or adjust the parameters in OpenSCAD, render (F6), save...

Make sure you select your arduino model and com port. Extract the files There is a marlin.ino in there that you should select Then upload to your Ramps board and it should work, I'll test the sd card and lcd when I get the bits. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

At each joint- extend the cable to it's most strained position and then firmly secure it to the next joint in the chain with a zip tie. Example Setup:Though I tested all of my parts and you can assemble in any configuration you like, if you want...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 48...

The source of the model has several parameters that you may wish to change. The current settings are for a silicone tube with an internal diameter of about 4 mm. You can adjust the pen length and width to your preference. Note that some tweaking may...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Assembly Video: https://youtu.be/GqohsdSTQrc Using"2mm Male Female Banana Plug Connector for RC Model ESC Motor Speaker" to convert Foster Connectors to electrical connectors -concentric BNC like. The printed parts hold these 2mm contacts in place...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

I thought about being edgy and calling this v6.66 but I figured a name change would provide a clean slate for the community to build from.Starting with my printed Gecko 1.0, I painstakingly modeled the entire blaster in Fusion360. There were three...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 34 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I have left the original design files as well to preserve version control. Design File Included: .f3d, .ipt, step, .skp, and .obj files. Follow The Makers Workbench...

... Use your best judgement if you have more experience at printing. This is my first upload, I am still struggling with FreeCad. Hence, the models might not be the greatest so please be kind. Use at your own risk but they work on my printer! ...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

Print Settings: - Printer Brand: RepRap - Printer Model: Prusa i3 - Rafts: No - Resolution: 0.2mm - Infill: 30% Notes: 1st Part to Print: "Bottom Mount" This part doesn't require any support material. It's the most complex print in this design,...