mcfarlane action figure stands 3d models

N Scale Train Trestle Display I put together these trestles to use as display stands for N gauge engines. One is 10.5 and the other is 5 inches long, but one could easily be made to any length. It is loosely based on a Great Northern Railway Standard...

A vice could also be used to seat them. The M4x10mm button head screws go though to the M4 locknuts and need to stand just a few mm proud of the base in order to catch the holes in the base of the switch. It will be a bit of trial and error, but when...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-C is approved for use within environments where flammable or combustible gases,...

*Barrel: print standing on the breech, like a smokestack. *<strong>Axle</strong> (2): print with axle tip pointing upward. *<strong>Wheels</strong> (2): print flat. *<strong>Wheel Caps</strong> (2): print with opening pointing upward. *<strong>Spring...

It also allows performing exercises standing at the barre! With the leg strap you can tie the foot stretcher on to the upper ankle. This allows your knee complete freedom to bend and stretch, enabling you to perform a greater variety of dynamic...

The bottom stand doesn't allow for the vertical adjustment needed to set the water lever within the filter Body, other than simply cutting the legs to desired height. The side hanger though required a change to grate pattern in the Body so they're...

Finally, the person standing in front of a closed door is one who is hungry for knowledge or change. An open door always has a positive meaning - new opportunities, overcoming obstacles, freedom and clarity. The tarot (/ˈtæroʊ/, first known as...

This is a free-standing HEPPA vent to attach to the end of a 4" (101mm I.D.) vent hose for 3D printer & laser engraver enclosures. There is plenty of extra room in the filter compartment for activated charcoal/carbon filter sheets. This project...

You will need to communicate with your robot, to say it to go forward or back, to turn left or right, to stand up or rest. You will need to make or look for a driver for the communication you want to use with the robot. I used a HC-05 bluetooth...

Crafting a reservoir-themed solution for a contest assistant In order to take part in the competition, I will design an innovative reservoir cover that stands out from the rest. This will require creativity, attention to detail and a thorough...

With that said, with the letters mounted on the wall split into two rows of the words "hello" and "world!", this entire sign measures a maximum of 790.5mm X 384.2mm X 50 mm (l X w X h) with the letters standing up mounted on a wall. Every model...

 Once you have it all assembled with as much slack removed as possible, tighten the fasteners *to where you still have the ability to tug a bit of slack - so snugOnce you have the light and all the stand column parts at this point, you can pull the...

Sambucca stands for "Smart Arduino Microcontroller based useless but crazy n 'cool automotive" Nice name right? Behind this is a small project of mine, in the course of which I want to cram as many sensors, actuators and breakboards for the Arduino...

Then he flew, as casually as he could, to stand next to the tall girl. "Your red dress is so cool! Does the color mean anything?" Zoe asked. But her attempt to start a conversation was in vain. As she spoke, the interesting boy pulled the tall girl...

You probably could print the model standing on the big flat side, but I recommend to print it flat. This also prevents trouble when your printer is not calibrated properly. A misaligned x axis will just cause a smaller/bigger length of the connector...

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This 0-10V dimmable fixture carries a T6 temperature rating and is approved for Class I...

The housing is specially designed to dissipate heat which increases the efficiency and lifespan of the LEDs and electronics.Suggested Applications: The EPL-HB-150LED-RT-180B is approved for use within environments where flammable or combustible...

The battery backup unit includes a switched leg for turning the light fixture on/off without kicking the unit into emergency mode.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division...

The base knife block stands 5in (12.7cm) tall, and accepts 13u of panels. An optional adapter can attach to the bottom which tilts the block forward either 5 degrees, 7.5 degrees, or 10 degrees. Note that I have not tested these in practice, so it...

A bolt length of 30mm is as short as I would go, but longer will work just as well, if not better.Work the SuperPINDA Precision Adjuster onto and off of the SuperPINDA probe (or stand-in M8-1.0 bolt) several times to “break in” the part. Depending on...

"DGB" stands for "Direct Gopro body". Literally cutting out the middle man, which is the adapter Changelog v1.5 - Removed v1.4 and older files (Rip Stats again) - Main bodies take into account the D1 mini antenna poking out by .1-.2mm -...

For the naitive Solidworks files please see the Github. Print instructionsThis design stands on the shoulders of many great designers of Crossrod Gantry Printers that came before it. Most notable of these is the design of the original Eustathios by...

Since all my windows have a small ledge I decided to make the array, "stand alone' so it would make it easier to move from one location to another or reverse the fan air flow. The base can be used on the bottom corners of the array or extras can be...

DO NOT RUN THEM STAND ALONE (they will not work or may harm your printer). Follow the instructions below: First open your STL file in CURA and slice it with your own preferences. In CURA: Goto Extensions/Post Processing/Modify G-Code/Post...

Once standard electrical power is restored, the emergency battery pack will be recharged.This fixture carries a T6 temperature rating and is approved for Class I Division 1, Groups C and D, Class I, Division 2, Group A, B, C and D, and Class II,...

N Scale Train Trestle Display I put together these trestles to use as display stands for N gauge engines. One is 10.5 and the other is 5 inches long, but one could easily be made to any length. It is loosely based on a Great Northern Railway Standard...

The four foot long LED tube design bulbs included with this unit are rated at 50,000 hours of service life, which is over twice as long as standard T8 bulbs.This 0-10V dimmable fixture carries a T6 temperature rating and is approved for Class I...

It currently stands as a prototype, a proof of concept that 3D printing is a viable option for manufacturing PCBs. On the other hand, for those who are interested to print and test the device, see the printer’s note and the components list, and to...

Model made as 1/35 scale.Dimensions: - After being printed will stand: 85 mm tall, 105 mm wide, 241 mm deep; - Small parts should be printed at 100% infill to make them solid.WHAT WILL YOU GET AFTER PURCHASE?- STL files of Tiger I Tank for printing...

This is a free-standing HEPPA vent to attach to the end of a 4" (101mm I.D.) vent hose for 3D printer &amp; laser engraver enclosures. There is plenty of extra room in the filter compartment for activated charcoal/carbon filter sheets.</p><p>This...