mavic 2 pro 360 camera mount 3d models

I designed this for my Ender 3 Pro it holds my camera so i can watch my prints from octoanywhere. To hold the camera to the swivel mount it uses the original pin and screw. I added the test swivel piece so you can print it and make sure it fits your...

Check out this YouTube video for a demonstration: https://www.youtube.com/watch?v=0obJjOZDwAc But before you get started, make sure to pick up my bottom mount to keep it securely attached to the Mavic:...

A mount to use your iOS 16 MagSafe equipped iPhone as a Continuity Camera for an iMac Pro.See https://www.theverge.com/2022/6/7/23158510 for more information.Link to fork .shapr source file:...

A mount to use your iOS 16 MagSafe equipped iPhone as a Continuity Camera for an iMac Pro.See https://www.theverge.com/2022/6/7/23158510 for more information.Link to original .shapr source file. ...Alternative you could try a solution like this - <a...

Camera mount for ender 3 pro, ender 3 and ender 3 V2 Easy to adjust the camera position and easy to dismount if not needed. 3 parts, no extra hardware required. UPDATE : new and shorter version of the arm is available. Short is 45mm from base...

Spring-loaded Adjustable Tablet or Phone Holder for DJI Mavic Pro RC Controller To assemble this adjustable holder, use a 1/4 x 20 x 1 1/2 in socket head bolt and a 1/4 x 20 nut for the knob. The print orientation is exactly as shown in the...

Left side camera mount for ender s1 pro with TP-Link c-100 camera. ...&nbsp;Should work with ender s1 as well.But should work fine on an ender s1 as well.&nbsp;Just take out the screws that’s holding the plastic bottom in the corner and use those to...

... https://youtu.be/LdIxl0FUL3M Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .2 mm Infill: 20% Post-Printing Cleanup from supports requires some work, as this print will necessitate the removal of a few supports.

Blink go pro mount style bracket. ...Designed to use go pro style mounts. I found it pretty handy. ... its a tight fit, so it will not fall out of the bracket,

This is a printbed-level camera mount with a pedestal base for a wide range of webcam mounts. I am using a Geeni-style IP camera. The mount clips onto the printbed base. Approximate pedestal base width is 3". ...

I used these flashers: https://www.amazon.com/gp/product/B00L1UPKLC/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 Note that shortly after designing the original model, where the Getterback was mounted on top, I realized there was a 50/50 chance the...

this is a top mount camera/canopy. I printed in Polypropylene. Let me know what you think. ...Cheers!!!

A versatile accessory designed to complement Raspberry Pi cases equipped with 75mm mounting holes, this innovative device attaches securely within the handle hole of the popular Flashforge Pro.

The Mavic 2 Pro Back Arm LED Covers allow you to conceal the rear LEDs that can't be turned off, making it possible to fly undetected. Simply print out these covers, attach the caps and add some soft Velcro inside where the LEDs are located, and...

DJI Mavic PRO 2 + Smart Controller - Expertly Modeled with Precision. ... Files included: *.max (fully optimized for use in 3ds Max 2015, with Corona render engine enabled) *.max (equally optimized for 3ds Max 2015, this time featuring V-Ray as the...

I originally intended the camera mount to resemble the one in the picture you see now, but I have modified it slightly and mounted it upside down making it more discrete and compact. I will soon post pictures as I am doing a test print to determine...

This hole is specifically designed for attaching the camera to various mounts and accessories, including tripods. You'll need a compatible adapter or mount that fits onto this thread, ensuring a secure connection between the camera and tripod. Once...

Held on with slight pressure from print top and bottom as well as 3m command strips. ...I did use a lighter to gently heat up the arm to bend it in to get the angle that I wanted. Uses a go pro style mount in conjunction with my arducam.

This is an uncomplicated payload rapid deployment system specifically designed for the DJI Mavic Pro. Absolutely no servos or electronic components are needed. ...Additional solitary component files were uploaded on April 19th.

Here's another camera mount I designed, which cleverly utilizes the 3mm bolt location on the underside of the case. To assemble it, you'll need to replace the factory screws with longer 3mm screws. I created a slot in the upright so that you can...

This is a 19mm camera mount to be used together with big Air Unit on the top hatch. To be glued in front of Air Unit with some Uhu Por or like it. ... Height is enough so that GoPro (even 10) under it is not visible in FPV feed.

I needed to figure out a way to have a charger stay in place, and found a great model from @art_fpv. ...I added some feet to either help it stand up, or be screwed in.

Should work on DJI Spark / Mavic Pro / Mavic Air / Mini SE. It acts as a joystick protector/cover(and fits in the case) and when expanded can be used to hold your mobile(especially if your phone has a thick case like mine) Three piece body * Base +...

https://www.thingiverse.com/thing:2735968 This is the third version of a tablet and phone holder for DJI Mavic Pro / Platinum or DJI Spark remote controller to have it behind antennas. As usual, mounts are designed to be under the controls this...

Check out v4 https://www.thingiverse.com/thing:2735968 This is the 3rd version of a tablet and phone holder for DJI Mavic Pro / Platinum or DJI Spark remote controller to have it behind antennas As usual mounts are designed to have it under the...

This is the 4th version of my tablet and phone holder for DJI Mavic Pro / Platinum or DJI Spark remote controller to have it behind antennas As usual mounts are designed to have it under the controls this will give you the feeling of old Phantom...

This is the 5th version of my tablet and phone holder for DJI Mavic Pro / Platinum or DJI Spark remote controller to have it behind antennas. As usual, mounts are designed to have it under the controls, giving you the feeling of old Phantom series...

Weight : approximately 1.6g - Pure Nylon Infill Material Fits Most Toy Whoop Frames : * Furibee F36, Eachien E010,E011,JJRC H67,JJRCS H36 * Blade Inductrix and other frames with pop-on canopies Comes Equipped with a Cam Holder for 10mm Lenses (most...

I printed in standing position because I wanted the mountholes to be perfect. ... So you need suppport all over but you can try to print it flat. I used brim to. How to disamble your camera ,search for 'c920 disassembly' on google.

I made this mount so i could attach my Mini 3 Pro RC controler to my bike. Great when using auto track. I have a handlebar stem gopro mount as shown in the photo but it could be used in many ways. ...