maverick 88 grip

Hercules - QIDI X-Max Carriage for BMG & Dragon / E3D V6
prusaprinters

I used heat shrink tube on both thermocouple and heater cartridge but it's optional, it can be easier to get the pin header to grip by doing so. The thermocouple can be a bit difficult to work with so take it slow.Notice! If you get a temp drop when...

EnderLoop
prusaprinters

Note that it's going to take some patience to get a clean surface and the performance (adhesion and ability of the roller to grip the belt) will be worse than option 3. The price point for this option is also going to be about the same as option...

T-800 Endoskeleton 3D Printing Figurine | Assembly + Action
gambody

The 3D printing model's chosen scale is 1:4 for FFF/FDM and DLP/SLA/SLS versions.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 129 parts;- A printed model is 470 mm tall, 217 mm wide, 187 mm deep;- You can light up the model's...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
prusaprinters

I used heat shrink tube on both thermocouple and heater cartridge but it's optional, it can be easier to get the pin header to grip by doing so. The thermocouple can be a bit difficult to work with so take it slow.Notice! If you get a temp drop when...

CR-10s Pro V1, CR-10s Pro V2 and CR-10 Max Maintenance, trouble shooting and upgrade guide
prusaprinters

https://youtu.be/EvG4uqx-Oos)  Maintenance:Since the printer come with a bowden setup equipped with a dual gear extruder (creates a hell of grip), an original Capricorn PTFE tube and a regular hotend (where the PFTE tube is directly...

Full Build Instructions for Slack Lack (Ender 3 / Ender 3 Pro) Plus Accessories
prusaprinters

Note that the cable grip should be facing away from the back side of the table. Install the legs on the bottom of the second tabletop. This one is awful - those double-ended screws are impossible to get a grip on. Instead, use your power drill, fit...

Hercules - QIDI X-Max Carriage for BMG & Dragon / E3D V6
thingiverse

That way they fit in the holes of the extruder like picture and stick out about 4 mm so there's plenty of grip in the threads of the stepper motor while not being too long so they bottom out. Shorten the PTFE tube that came with the Dragon...

Self winding pendulum clock (climbing weight for weight driven clocks)
thingiverse

This provides a more reliable force transmission than the grip and/or glue between the shaft and the ratchet. **3** A "top point stopper" (CW_CLOCK_stopper.stl) has been created so that the weight does not collide with the dial plate or the clock...

Jules Verne Train Locomotive 3D Printing Model | Assembly + Action
gambody

The 3D printing model’s chosen scale is 1:32 for the FFF/FDM version and 1:64 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 142 parts;- A printed model is 168 mm tall, 240 mm wide, 448 mm deep;- Gull-wing...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
thingiverse

That way they fit in the holes of the extruder like picture and stick out about 4 mm so there's plenty of grip in the threads of the stepper motor while not being too long so they bottom out. Shorten the PTFE tube that came with the Dragon...

Ornithopter Dune 3D Printing Model | Assembly + Action
gambody

The 3D printing model’s chosen scale is 1:64 for the FFF/FDM version and 1:128 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 61 parts;- A printed model stands 368 mm tall, 456 mm wide, 560 mm deep (platform +...

IKEA Lack Enclosure (3 Variants, modular)
prusaprinters

Install the grip with two M4x16mm screws (do not forget to insert M4 Hex nuts into the back part of the grip).         [red] thin wall must be oriented to the longer side of the glass panel.[green] Inside...