maverick 3d print

This bumper is for 1/10 onroad HSP/Himoto/Maverick models. The design has been little bit reinforced. 2,8 mm hole for M3 screws. 3,2mm hole for 3 mm pin. P.S. ...: I will share the other hsp parts in another post soon.

I crafted a sturdy three-platform plywood setup to upgrade my Maverick Scout's plastic components, allowing me to pack more gear onto it. The flat panels are constructed from durable 3.5mm thick plywood, while the four supports are fashioned from...

this is a direct replacement for the tie rod on the Maverick ION series. ... if your printer is having difficulties getting the hole to be good enough to fit on the ball, just unscrew the ball and attach using the threads on the back of the ball

This rear hub is for 1/10 onroad HSP/Himoto/Maverick models. 3,2mm hole for 3mm pin. 2,8mm hole for screws. The marked side will be on the front. P.S. ...: I will share the other hsp parts in another post soon.

Wanted to make the cubby in the new for maverick a bit more useful. Threw this together, to place a fits slot and change holder in there. It is still a work in progress, and might require some velcro tape to keep it in place with weight on...

More details in this blog post: https://mod.blog/2022/04/30/2022-ford-maverick-bed-lights/ These mounting clips are designed to nestle in on the tabs holding the plastic cover on the sides of the bed of your Ford Maverick. There's 8 on each side, so...

The Maverick is the main fighter aircraft of the Midpyrenean Realm. While less maneuverable than lightest aircraft, it boasts heavier armour, a greater fuel capacity and can mount heavier armaments. Like pure bomber it is capable of both atmospheric...

I've been tinkering with this FORD MAVERICK CONCEPT since 2015, when I first fired up Lightwave 2015 to bring it to life. Over the years, I've refined and revised my model, initially aiming to craft a truly unique concept that would mirror the...

This fits into the Ford Maverick FITS slot behind the center console. This is as close as you will get to the official thing until Ford releases their CAD models. You can add anything you want to this piece. (cup holders, trash can adapter etc.) ...

Ghost of Maverick is a special project of mine—my personal endeavor. It stands about 19" high, and you may need some extra parts, which I obtained from Amazon. This project is continuous, as I'll be uploading weapon packs and upgrades for this beast....

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The rest of my settings were autoapplied via the eSun PETG with 0.4mm nozzle extruder...

For a full print you will need: 2 x Hips 2 x Legs upper 2 x Legs lower 2 x Foot 2 x Ankle 4 x Ankle Retention Bolts (The smaller ones) 6 x Upper Retention Bolts 6 x Toe Bridge 6 x Toe 6 x Toe Clamp Left 6 x Toe Clamp Right 1 x Everything else You...

I made a couple of changes to my original design: made the sides lower so it would print faster and use less material made a cutout in the side facing the seats for access to the USB adapter all so printed it in Orange ABS to go with the truck

Real simple print. Uses approximately 128g of filament. Recommend PETG for the heat that can accrue in vehicles. Update: 7/5. Adjusted rear angle to sit more level in console. ... Added a ledge in middle pull for easier grip with fingers.

... off the design by Kl0ck, but remade with the official CAD geometry provided by Ford for a better fit in the mount. ... Also features slightly bigger openings with better angles to fit large Yeti-style tumblers. Print upside down, no support needed.

Links for all the parts used in this build: Mayfly Kit: https://www.prusaprinters.org/prints/126863-nerf-maverick-mayfly-flywheel-conversion-kit Maverick Stock Attachment Point and Slide Replacement Thingiverse:...

Spaced out mount so that MA1 tucks under console on my Ford Maverick. ...Pictured in flex PLA, but later printed in PETG which was much better.

It replaces the existing muzzle, which can be removed after the blaster is taken apart.This muzzle can be used on a stock Maverick but it is also compatible with my Mayfly Maverick Flywheel Conversion kit.Thingiverse links for all the parts used in...

In a class assignment, our group decided to dissect and analyze a chosen item, opting for a Nerf gun as our subject of interest.

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

Customized version of https://www.thingiverse.com/thing:2592302 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2592302

Customized version of https://www.thingiverse.com/thing:2592302 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2592302

Game: https://www.youtube.com/watch?v=LgniEjI9cCMIf anything is missing, here is a link to the partner space with a clean set of files. ...Some of our parts are in a separate directory that we weren't supposed to...