material combiner blender 3d models

 No hole saw or CNC cutter required, I only needed a box cutter to get the job done!Pieces to PrintFan Housing (required)Fan Grille (required)Electrical Box Cover (recommended, unless you want it open all the time)Cable Pass-Through...

Material: PLA, ABS, ASA. PET also might be sufficient. All parts should be printed in their original positions.Only Z_motor_mount_L require simple supports in one place.You need:1 x Z_motor_mount_L1 x Z_motor_mount_L_bracket1 x Z_motor_mount_R1 x...

I used a white led strip but an individually addressable RGB led strip is going to be fitted and I will update the guide once it's finished.Materials need:chipboard (2 cm thick enough to cut out 2 circles with a diameter of 500 mm) or one sheet of 4...

For example, the recommended drying temperature for PLA is around 45~50C, use 45C instead of 50C.***If you use different materials or parts please perform a similar test before drying to confirm the temperature overshoot is within a safe range.Data...

For children, the colours should be appropriate for children. The clock face can be customized with the number cubes for practicing clock times.There are a total of 6 different ways to insert the cubes into the case, with the letters (AS TIME...

Anyway, if you were looking for the happy little elf movie like at the beginning of a series of unfortunate events then this isn't it and you should go to the other theatre.BOM (build of materials):Headset:esp32 dev module 30pin ~$3.50 on...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

Current version is not compatible with the landing gear that is created and is being tested GENERAL State Simple version Nozzle 0.4 mm Layer height 0.2 mm Shells 2 or 3 Supports none Material PLA or PETG Multi color print yes Colors...

Supporting this project is a guaranty for you that it will continue and become better and better.Buy MediaMan3D a...

Additional materials needed: * 30x 3/8” ball bearings (at minimum) * 10 M3x6 screws (or longer) * 1x M2.5 set screw * 1x Arduino Nano (or equivalent) * 1x DRV8825 stepper motor (or equivalent) * 1x Nema 8 (20x20x38mm) stepper motor (the shorter one...

The spool should be able to slip over the material without jumping. I used [this "Holed mat"](https://www.bunnings.com.au/moroday-450-x-450-x-3mm-black-self-adhesive-holed-mat_p4000017) from Bunnings, but if you're not in Aus you may have to find...

And they are not landing a massive starship for your scrawny hide!Then comes the Armoured Transorbital Shuttle!Built of high-class materials, it will carry the lowest foul parasitic hive scum to the upper stack rarified air breathing elite class (not...

 I am not responsible for the parts not going together if you stray from the bill of materials listed. Print Requirements:No supports!Parts are already oriented properly for printing, do not flip them (rotation is fine).Designed with 0.4mm...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

Once that's done, make sure the screw holes are unimpeded by any support material if you have used supports (I didn't need to) Add the heatsinks to the Pi's, and plug in the CSI cable from the wide angle lens into the bottom Pi. Screw in the...

If you have difficulty, make sure all the support material has been removed from the handles first, also, the nuts go in at an angle. The M3x30mm screws will be used to mount the handle during final assembly.</p> <p><strong>Putting it together - Step...

For more info describing how I built my panels (which are pictured), you can find a build log on my site here (includes the Bill of Materials): http://www.mystoopidstuff.com/hexled-panels-assembly.html I also posted some info here on how to get the...

well, this will tell us!Note: this piece is a remix of a pluviometer made for ZigBee door sensor (Aqara) so is some way this is ZigBee capable.Original project from https://smartsolutions4home.com/ss4h-zrg-zigbee-rain-gauge/Control BoxWe need...

Links to materials: M3x8mm screws Magnets 10x5mm for enclosures Magnets 10x2mm for flywheels Aluminum rod 5 mm Bearings 12x8x3.5 Motor PWM speed controller DC-DC step-down module 5.5mm jack Touch button MOSFET LED Strip Double...

well, this will tell us!Note: this piece is a remix of a pluviometer made for ZigBee door sensor (Aqara) so is some way this is ZigBee capable.Original project from https://smartsolutions4home.com/ss4h-zrg-zigbee-rain-gauge/Control BoxWe need...

17.10.23 - Cleaned outer ring up to be smooth and lessened by 1cm height to save print time and material yet allow the same secure hold with a cinch strap. 02.10.23 - Latest file (Hands3 revised and optimised) has better corning radius added and...

You can make the product on a 3D printer or cnc machine from plastic, glass, steel, clay and any materials. the model can also be made using cnc machine turning wood.Also the model can be executions in castings. If necessary, I can make injection...

(Support material is recommended for this part) **2** Shifter Shaft is printed laying on its side, again relatively high wall count and infill percentage, much the same as the main body. **3** Bottom Cover is simply to retain and protect the...

Thicker base, more material here, less there, on and on. So: Want the Latest Version? Missing your Quad? ND Filters?Message me! discord! The 60+ mount designs I've uploaded here (see files!) are updated after every tidbit of feedback I get and are...

It's got some slots cut into the top of it to allow any heat to escape so any material should be fine to print in. Mine has been on a LOT for the last week with nothing melted and everyone loves it! :) I've included Solidworks and STEP files if...

Aluminum heatsink 190mmx35mm (H) or 190mmx50mm...

25% infill (GRID internally [no clue how much this matters], CONCENTRIC on top and bottom layers [I like the way it looks but it may also help out my E-Mount and the alignment tabs]) was used on all pieces.The E-Mount portion ("mount.stl") needs to...

The bottle caps are securely airtight and can even preserve volatile materials like dichloroethane.For light-sensitive resins, I've chosen opaque black bottles to prevent light exposure to the materials. This way, the glue remains in its original...

Wooden Crates and LumberEven in the future, people need materials to build with. Plants, wood as the backbone of many a backward planet's building strategy. Wood is use to make exquisite furniture, paneled walls, and more. In the lower levels, its...

I recommend first using simple or pincer claws first as the multi-joint fingers take some tuning to get working correctly. Print instructionsI have printed all my parts for the Black Ram Hand in PLA and have tried to optimize the fit, clearance and...