masterforce miter saw stand mx77 3d models

Dust collection for Kobalt 12 inch Miter saw. Uses 4 of the magnets listed below, but honestly friction fits into place perfectly fine without them. There are 2 2-1/2 inch ports, but 1 is honestly sufficient if you're just using a shopvac; if...

I designed a zero-clearance insert to replace the standard stock insert on my DW715 Dewalt Miter saw. After several months of use, it still looks almost brand new with no significant signs of wear. The only caveat is that it needs a long bed, which I...

I designed a Vacuum Hose adapter for my Chicago Electric Miter saw, so I decided to test ABS plastic using my Fabrikator Mini 3D printer first. Therefore, I created this adapter with Tinkercad and then printed it on the Fabrikator Mini next. I also...

I'm modifying my Tool Shop Miter Saw to connect it directly to my dust collection system, using a Rigid Shop Vac as the host for the larger end of the adapter. I've customized the design based on http://www.thingiverse.com/thing:1246651.

Note: This was tested on a Harbor Freight Item #91995 ten inch compound miter saw manufactured by Chicago Electric Power Tools. ... You will need the original hardware plus the following: 2 each 1.25” ¼ – 20 countersink bolt (1” + head length) 1 each...

The lever on this saw stand had taken a beating and no longer worked. So I drew up a new one. ...Fits onto model DWX723.

I'm not sure what happened to my Ryobi compound, sliding miter saw's bevel knob - it just broke on me! The website I visited for replacement parts was no help; they told me the part is no longer in production. So, I decided to take matters into my...

I just replaced the cord-wrap bracket on my miter saw with one I designed and printed since no replacement was available. This marked my first attempt at using Fusion 360 for designing and 3D printing, but it turned out to be a success as the new...

Dewalt Table Saw Miter Gauge Holder This is a bracket to hold the miter gauge on the saw frame when not used. Currently dewalt has no where to hold it, that I can see. The protractor/angle gets set at 10 degrees, and then that guide will sit flush...

This is an exhaust chute diverter for a Dewalt Miter Saw, and it can work for other saws as well as long as the chute's OD (outer diameter) is 39mm.Notes on Usage:Print 2x 40deg elbows and and 1x 40deg fan-out (no vacuum required)If you want to use a...

Thanks! https://paypal.me/cdsmakestuff Miter Slot T-Nut for Table Saw or other tool with similar "T" slots These are probably (most likely) going to fail if you tighten them toooo much. But they should stay in place with minimal torque on the bolt /...

I needed a Vacuum Hose adapter for my Chicago Electric Miter saw and wanted to test ABS plastic on my Fabrikator Mini 3D printer. So I designed this adapter using Tinkercad, then printed it out on the Fabrikator Mini. I also coated the design with an...

This is a custom creation I made for dust collection on my DeWalt DW715 miter saw, which likely works with many other models as well. If you succeed with it on a different model, kindly share your experience. I adapted this remix from...

This is a zero clearance insert for Dewalt miter saws.I modeled it from the insert on my own saw wich is a DW716 (12inch, dual bevel, NON sliding)from what I can tell from the replacement inserts on amazon, this will fit...

If you have the Rigid (Home Depot) 10" Miter saw with the laser line (model MS1065LZA) the insert plate (the orange plastic part) will eventually crack. I couldn't find it on the Rigid tools website but figured, it would work just fine as a 3D...

Miter gauge slot for Delta 36-725T2made for pairing with this featherboardhttps://www.thingiverse.com/thing:1795001https://www.thingiverse.com/MarcElbichon

The cord-wrap bracket on my miter saw broke and there is no replacement available so I designed and printed one. This is my first attempt at Fusion 360 and printing. It fits and it solved the problem so I call that a success!</p> <p>If you print-one,...

- Saw Connector Test Fit: This end goes onto the saw - it should slide on with just a little resistance and twist and lock securely onto the dust port's lugs. - Hose Adapter Test Fit: Fits over the 2.5" dust collection hose, which is sized to slide...

- Saw Connector Test Fit: is the end that goes on the saw -- it should slide on with just a little resistance and should twist and lock securely onto the dust port's lugs. Hose Adapter Test Fit: fits over the 2.5" dust collection hose. This is...

This is the washer that holds the blade guard on the admiral table saw (model 64686). Works great for me. ...I printed it in PETG.

No supports necessary. ...Fits my DeWALT D27113. Vacuum hose has ~39mm OD and 5.5mm pitch. 36mm opening for the vacuum and 40mm on the saw-side. ... Find STEP and Fusion360 files in the downloads.

First draft upload. ...Scoured through search results for a compatible design, ultimately settling on a plate intended for other types of saws, unfortunately none were available specifically for the Ridgid model.

... this assembly. Most of us probably use our sliding saws as chop saws anyway, so we won't be affected by this limitation. ... Printer settings: Infill: 45% Perimeters: 2 Layer height: .2mm Check out my Google page and give me an upvote - thanks!

Zero Clearance Insert for the Hitachi 10FCH2 Saw (Should also match the Metobo C10FCH2). Works fantastic, just needs some minor adjustment to avoid sanding to install. I will fix the fit just a bit in the next revision I produce. ...For now, if you...

The part of the guard that attaches to the saw is notorious for breaking and is often installed wrong from the factory. ...I used a broken guard to model and print a new one for a coworker and it works great!

Work in Progress: Update 6/16 - The feather board connector 02 is modified to fit more securely into the HF saw slot and accommodate stock screws that came with the HF / Chicago Electric feather board. A washer was required to make v01 work with the...

I made this model for a past teacher of mine who had two of these saws and the second one was missing the outlet cover. I had to sketch around the outlet because there was no straight line to measure off of. I then imported the picture into...

Fits my DeWALT D27113. Vacuum hose has ~39mm OD and 5.5mm pitch. 36mm opening for the vacuum and 40mm on the saw-side. Find STEP and Fusion360 files in the downloads. Testlink:...

Needed rails for a cross cut sled that fits my SawStop table saw can be custom-made with standard measurements in mind. To facilitate this process, I've attached the Fusion file so users can easily edit and tailor it to their specific needs. I...

This will allow full movement of the saw without interference. As of February 17th, 2017, it's only been in operation for about a week, so I'm still testing it. My OEM part shattered about a year ago and I've been doing without it, so I took good...