masterbox q300l ssd mount 3d models

This is a mounting bracket for a second 3.5 HDD that can be installed in your Cooler Master Masterbox Q300L. Story: I'm building an HTPC and needed another 3.5 HDD to install in my case. The original design only allows one 3.5 HDD, so I created this...

I designed this bracket specifically for a Cooler Master Masterbox Q300L, providing an additional mounting point for a second 3.5-inch hard drive. Originally, the case only accommodated one 3.5-inch HDD, so I created a bracket to fit in front of the...

Clever CoolerMaster MasterBox 5 Lite owner seeks optimal SSD installation solution - a sturdy 15-degree angled support system.

... holes and cut them roughly. I mounted the mesh in between the case and handle, so it doesn't move around but you could easily also cut an exact shape of the handle and slice the middle portion so you can remove it without taking the handle apart.

The masterbox Q300L doesn't have really good airflow because apparently the holes in the panels have bad spacing and the fans are basically attached to this panel, so even with 4 fans in the case I was still getting quite high temps. To alleviate...

The Q300L has clip-on plastic bars in every corner that can be taken out and swapped around as neccessary for your case configuration. This thing replaces one of those bars with a custom one with mount holes. I've used it to add a headphone holder...

This is a fantastic headphone holder designed specifically for the CoolerMaster Masterbox Q300L case. It easily screws in from the bottom and perfectly aligns with various combinations of holes on the top. So you can place it more towards the...

The Q300L has clip-on plastic bars in every corner that can be taken out and swapped around as neccessary for your case configuration. This thing replaces one of those bars with a custom one with mount holes. I've used it to add a headphone holder...

Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. ...Ender 3 v2 0.6 nozzle PETG Category: Computer

Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. ... Ender 3 v2 0.6 nozzle PETG

Mount four 3.5 inch hdd on a 140 mm fan mount. ...The extra 8 holes are for stability and works on Coolermaster Q300L and Q500L cases. Ender 3 v2 0.6 nozzle PETG Category: Computer

This is a bracket to mount a second SSD on a Coolermaster Masterbox case. The orginal piece is out of stock so i've tried to make a copy fromt he one present in the case. The final result is quite good, and I've been used it to mount the second...

The Handle and Decoration Panel is a standout feature of the PC case Cooler Master MasterBox Q300, designed to add a touch of style to any setup. To install it, you'll need screws with a UNC thread size of 6-32 and a length of 5/8 inches - these can...

I've designed a custom SSD support specifically for my Cooler Master Masterbox Lite 5 Case. Since I'd purchased an additional SSD but lacked another support, I created this one to fill the gap. The third image depicts a previous design, which I...

This is a computer case thingie to hide a computer PSU.

Extended height foot increases airflow from the bottom. Total height is 18.5mm, compared to around 8mm stock. To edit the design, visit onshape.com and access the public document. ...The document ID is 515a01c6f666f557669986df.

Easily snap the third fan into place at the front of your CoolerMaster MasterBox 5.

HDD bracket that adds an extra HDD (or SSD) mount to the bottom of a Cooler Master Q300L case. Can be used with 2.5" and 3.5" drives, so pretty much all of them since it used the mounting holes at the bottom of the drive. To mount the drive...

A simple holder for earbuds. ... Category: Computer

A straightforward container designed to securely store earphones.

<p>A simple holder for earbuds.</p> Category: Computer

This bracket/plate allows you to mount a Raspberry Pi Model B in one of the few mounting locations for 2.5 HDDs. ...My plan is to use this RPi to drive an internal display for a case mod project.

The pegs on the back are designed to provide a stand-off and match the depth of the mounting pegs in my chassis - you could remove them or adjust their height to suit. ... Print Settings Printer: Anet A8 Rafts: Yes Supports: Doesn't Matter ...

Mount a high-performance solid-state drive directly into a standard 3.5-inch drive bay.

The device is adaptable to both wall-mounted and freestanding installations, as I was unable to find a suitable solution that met my requirements in either category. Using Fusion 360 software, I created this custom mount from scratch. ... The mounting...

2-part security mount for Samsung T7 SSD Installed in computer lab!

This is a remix of the iMac HD Mount to fit the a Seagate SSD.

For mounting a 2.5" SSD to the underside of a 3.5" HDD. ... Useful for unconventional HDD mounting locations.

Thanks to Psych0o on Thingiverse for the design and including the STEP file. ...I've simply modified it to support M3.https://www.thingiverse.com/thing:4565701 Here is the original design that supports M5 25-30.

<p>Thanks to <a href="https://www.thingiverse.com/Psych0o">Psych0o</a> on Thingiverse for the design and including the STEP file. ...I've simply modified it to support M3.</p><p><a...