maslow m2 vacuum adapter by 3d models

Replacement part for a broken Intex Pool Cleaner adapter. ... The one end is for a 32mm pool hose, the other is put into the skimmer.

Purchased this off amazon to use with my shop vac: https://www.amazon.ca/gp/product/B077SDD6Z6 Made an adapter for the Dyson Clone NEQURE A18.

ORIGINAL I printed this for my vacuum bags. If filled with 1000g spools the valve has to be supported. I used some wood before, but I had to hold the pump at an angle to let the air out. Place below the valve and set the bag on top, then insert...

The vacuum from your shop-vac will suck up any debris as it is being produced. I printed mine out of clear PETG so that as much light as possible will be able to get through. The STLs and gcode supplied here are for a 45mm hose. If you need...

My mind started racing with an idea - what if I attached the hose from the compressor directly to the vacuum? This simple modification would make it a breeze to use the hand vac in tight spaces, making tough cleaning tasks a whole lot easier. Take a...

The vacuum from your shop-vac will suck up any debris as it is being produced. I printed mine out of clear PETG so that as much light as possible will be able to get through. The STLs and gcode supplied here are for a 45mm hose. If you need another...

... empty my pool after the season. ... Whith this adapter i can use my sandfilterpump to empty it to the bottum in a short time. ... I also made a connector to my standerd intex dirt removal set so i can fastened it to the border so it doesn't slip away.

On BoboVR M2: Remove the back strap from the front assembly on bobo vr by unscrewing the screws on the inside of the ring, then using a flathead screwdriver push pull the button piece off the outside, and after that push in the 3 snap-fit tabs to...

Customizable big-to-small hose adapter lets users adjust the inner or outer diameter to suit their needs. ...Its performance has been thoroughly tested and proven effective in PETG materials.

I began with Vince94520's design and adapted it to suit my 2.25 inch Rigid Wet/Dry Vac. The result is a perfect match! ...I'm grateful to Vince for his contribution.

<p>After extrusion, twist with the top and bottom to peel off the support. ...Before twisting the hose into the adapter, coat it with soapy water to reduce friction.

These adapters function as fully functional interfaces for the Makita VC-3 and comparable units. The fit is perfect for my printer, including the snap-fit, although results may vary as usual. A Fusion360 file is included for seamless modification.

This adapter seamlessly connects a Dyson hose to a 1 3/8" crevice tool, and I've included the OpenSCAD file for modification purposes. The adapter expertly fits into the Dyson connector on the hose, bypassing the one on the tube altogether. Although...

... tape to attach it to the hose. I made a simple adapter that fits the shop vac hose and the Flowbee hose tightly. No leaks occurred. This was quickly created in Fusion 360. ...The file will be included if you'd like to modify it to suit your needs.

The vacuum from your shop-vac will suck up any debris as it is being produced.I printed mine out of clear PETG so that as much light as possible will be able to get through.The STLs and gcode supplied here are for a 45mm hose. If you need another...

The vacuum from your shop-vac will suck up any debris as it is being produced.I printed mine out of clear PETG so that as much light as possible will be able to get through.The STLs and gcode supplied here are for a 45mm hose. If you need another...

I designed this adapter as simply as possible so that I could print it once and it would just work. ...Both sides are press fit.This was purpose built for the shop vac and table saw I own so make sure to check the critical dimensions on your items match...

You require a rubber sealant for DN50 tubing, which functions flawlessly in conjunction with caulk tubes. ...Dimensions include Length (L) by Height (H) by Width (W) at 122 mm by 63 mm by 120 mm. ...Fusion 360 files are provided.

The original design was great but the exhaust part hits on the motor housing of the D26676 adapter. I took this design and pointed the exhaust straight out. It fits snugly (credit to the original designer) and I modified the exhaust a bit to fit a...

I made an adapter to connect a fume extractor hose to my laser assembly. ... Fume Extractor from Amazon: https://www.amazon.com/gp/product/B07ZHH5H7N/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 Bilge hose: ...

... connect the hose. 7. These adapters are perfect for DIY enthusiasts, professionals, and anyone looking for a reliable solution for their hose needs. 8. ...They can be used with a variety of hoses, including garden hoses, water hoses, and air hoses.

This Humanscale M2.1 monitor arm bracket bolts directly onto a monitor featuring 100mm x 100mm VESA mounting holes. To secure the bracket and monitor to the arm, a spring-loaded clip is used, requiring precise printer material settings for optimal...

... accommodate hoses of different sizes for added versatility. Set the outer diameter for each hose, and input a clearance amount in millimeters. The adapter will then taper from the specified clearance down to the OD to create a snug compression fit.

The adapter allows you to attach a standard hoover pipe to the sander, in place of the dust bag it comes with. The design is intended to be printed with something flexible like TPU. If you make it with something more rigid then you may need to...

The adapter allows you to attach a standard hoover pipe to the sander, in place of the dust bag it comes with. The design is intended to be printed with something flexible like TPU. If you make it with something more rigid then you may need to...

I have remixed it together with Tauro's adapter meant for a Bosch dust hose, https://www.thingiverse.com/thing:5456353 This fits my DeWalt 421 and 26453. I will upload it as a remix with credit to both originals. Usually on projects I have 2 or 3...

... allowing seamless integration of all stock equipment. ...The V3 hot end slides effortlessly into the Wade extruder, ensuring a smooth transition. Additionally, I've adapted the fan setup by rotating it a few times to accommodate the new design.

There are printable parts for BoboVr M2 installation to HP Reverb G2. These clips has 8mm offset, so your head strap will not touch headphones and you will be able to install it more comfortable. I've printed it with FDPlast PETG. Working well...

Wanted a slimmer version so created this one. ...But you need two parts per side. Carrefull if you use puley with your reverb: Cable need to be fixed to the bobovr. I'll create/adapt soon a part for this

I tried a couple models I saw on thingiverse and none of them worked.I decided to make my own with a mount similar to what the m3 has.The model is not great, and could for sure be improved, but I've tried it with and without the quest facial...