manual punch press 3d models

We highly recommend that you get acquainted with the “Assembly video” and "Assembly Manual" before getting down to the Engineer Juggernaut model.The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing...

We highly recommend that you get acquainted with the “Assembly video” and "Assembly Manual" before getting down to the Protoss Carrier model.The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have...

You can manually control the paper transport using the button. The potentiometer allows you to adjust the speed of the paper transport to match the writing speed. The motor and gearbox are purchased parts (a gearbox kit with a motor) as they have...

Secondly, be aware that the placement of the horn in the mouthpiece is critical as well (on the order of a layer height makes a difference so press the horn in to lightly pinch the rotor and then back the horn out by rocking back and forth making...

I removed a very small amount of material from the inner cone in the rotor and the siren whistle now WORKS INCREDIBLE!Secondly, be aware that the placement of the horn in the mouthpiece is critical as well (on the order of a layer height makes a...

At home, Scott locks himself in the bathroom, puts on a suit, presses some buttons and decreases many times in size. At this time he is contacted by Dr. Hank Pym. This is how the story about Ant-Man begins.ABOUT THIS 3D FIGURINEThis figurine is the...

Then, bend the shades and hold them together with the edge pressed to the table, and carefully push on the second bar from the TOP downwards. Don't get stressed, just keep the edges of the shades as flat to the table as you can with one hand and push...

Select all of the sub-objects by pressing Ctrl+A, then navigate to the "Shading" tab at the top of your screen and select the "Cycles Render" engine from the drop-down menu. This will enable you to render your model using the Cycles rendering...

The 8 switches to 0 when the lanekeeping button is pressed. Once everything is ready, find a nice straight road with clear lane markings. Begin the IPMA Lane Camera calibration procedure in Forscan. Follow the prompts and at 30%, a large...

They should be pressed to the pillars without loose, but allowing smooth movement through whole height of the frame.Take Z_motor_mount_L and put it into cut out place of the left pillar of the printer. It is designed to fill and fit the place,...

Make sure the wires are in position, put glue on both ends and press the rings together. Optional you can leave the bottom section without glue. In that case you need to ensure the gab is closed when gluing the socket onto the ring. When the...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

If you need to change them to use extruder 2 on your printer, you can select them all by CTRL clicking each of them in the object list and then set them all at once to use extruder 2 by pressing CTRL/2. Change any settings you want in your print...

If the Indicator PCB is pressed against the Stepper, then it will cant the central shaft and bind with the Thru Shaft. Alternatively, your circuits could short against the motor Alternative Designs/RemixesIf you're feeling adventurous, here's some...

This is done by 4 screws from the bottom which press the rolls against the extrusion. This can be done by directly clamping both carriage parts together with the screws or using some spring loaded screws if you find some small springs (same concept...

She lures it into a hydraulic press which crushes it. Months later, a pregnant Sarah is traveling through Mexico, recording audio tapes to pass on to her unborn son, John. At a gas station, a boy takes an instant photograph of her and she buys...

This should be a press fit, however, depending on the printer and chosen resolution, if it is not, it is recommended that this is taped in place.  The other wing nut(6) is then threaded onto the carriage bolt in the same orientation as the first,...

See the Create your own section for more information about building a custom model.This project uses the the T-Nut mounting system created by @6d6178 to attach to the pegboard itself and uses BV3D's method to print indicators on the first layer in a...

Press the button on the hot glue gun and coat the hook in hot glueWhen screwing the handle part, be careful that if you screw the hook too far in it might split. We had this issue many times and broke a few hooks.The handle part with a hook:Use flush...

Make sure the wires are in position, put glue on both ends and press the rings together. Optional you can leave the bottom section without glue. In that case you need to ensure the gab is closed when gluing the socket onto the ring.</p> <p>When the...

* Be careful not to bend the LED strips sharply. I allowed the LEDs that fall in the corners of the boxes to "float", the LED Strips should not be pressed into the corners which could bend them too sharply. * It would be a good idea to bench test...

Make sure the wires are in position, put glue on both ends and press the rings together. Optional you can leave the bottom section without glue. In that case you need to ensure the gab is closed while gluing the socket onto the ring.</p> <p>When the...

Line it up and press to the surfaced. Remove transfer tapee. Experiment on a spare piece of wood if you need to, sometimes putting a clear coat first then applying the actual paint can help a lot with bleed where paint soaks under the tape if its...

Insert the 2.8" Display Module into the Adafruit Proto-Screwshield (Wingshield), being careful not to press directly on the screen, as you could damage it. Finally, connect 5V power to the 2.1mm jack and, after a few seconds, you should see some...

(you will have to cut it after casting) trace of silicone on the outer side of one of the flanges of one of the mold pieces.Take another mold piece and press the matching flange on the flange you just pasted with silicone. Align the flanges carefully...

The enclosure is just pressed together. Barrel Jack Connector eBay Search: 5.5 (2.1,2.5) panel connector The connector was added after I printed my lamp, but you can still see it in the test model. I just used a wire in my lamp, which doesn't look as...

Press firmly with screwdriver to ensure it is fully seated.Slide the Carriage Clamp Arm onto the front right arm of the Y carriage.Insert the M3 x 30 mm screw through the hole on the front clamp wing into the nut at the rear and tighten. Assemble the...

Enjoy and reposition plates whenever you want, you can even move the main module and remove connector by pressing with your finger to unsnap two modules (Refer to step 5 to unconnect modules)Optionnal Step :&nbsp;&nbsp;You can print and add finisher...

If the screws are not seated properly into the depressed cavities before pressing the drive onto the x-axis plate, your Mosquito will not sit flush against the Blood Drive and/or you will strip the Mosquito's threads. As this is a depressed fit...

7) Insert the 2.8" Display Module into the Adafruit Proto-Screwshield (Wingshield), being careful not to press directly on the screen, as you could damage it. 8) Finally, connect 5V power to the 2.1mm jack and, after a few seconds, you should see...