manfrotto replacement parts 3d models

I created this in response to some broken parts on my KO Optimus Prime action figure. I also designed them to act as upgrades to the original parts. ... Also, despite what the print settings say, I actually printed these on a customized Voxelab Aquila...

I've updated the design to incorporate a three-pole component, These parts are engineered specifically for a pole diameter of twenty millimeters, with a hole measuring twenty point eight millimeters. ... I manufactured this item using PLA material with...

I've updated to include a 3 pole part, its a quickly rehashed part, but should work ok I've included a 3 pole version with reinforcing fillets on all sides. There is a version of this part that is completely hollow at the intersection, this is the...

This is a remix of https://www.thingiverse.com/thing:4687836 broken into two parts so that it can be printed both with less supports, and in structurally ideal printing orientations. Print the parts in the default orientation, which can be seen in...

This text describes a set of designed parts, including Top Bracket, Hinge Bracket, X-Bracket, Broken Piece Splints, and Feet. It suggests printing the pieces with strength in mind, at least 60% to 80% infill. Broken arm splints should have a 90% to...

The original SKS M59/66 model was purchased from ZVC, and I converted it to the Soviet standard SKS.Note that I will not share the original model, if you need the original model, please buy it from ZVC (https://www.youtube.com/c/3DPrint_zvc), then...

Small replacement drawers for hardware cabinets are now easily accessible. I created these because the clear, brittle plastic drawers would break too easily, and buying a new $15 cabinet was just not feasible. There are three different drawers: -...

I made this repair part for a buddy of mine.\nIt's been updated to include a 3 pole component, it's a reworked version but should function just fine\nA 3 pole version with reinforcement ribs on all sides has also been included.\nThere is an...

This is a remix from https://www.thingiverse.com/thing:4757607 I made it by using PLA but the ring part was broken due to the thinness of the upper (near the clip) line. So I added same total thickness as side wall lines there. it's solved. Now...

i make a file from scratch to repair a ride on toy atv rubber tire was too hard on the traction for the small parts. its made to slip/strip to prevent destroy the gear box. ... feel free to modify and reuse!

These kid-friendly drum set components are an upgrade from the subpar originals that didn't hold up well. ...After those inferior parts broke down, I took matters into my own hands and created improved alternatives for kids who deserve better.

These are some parts I made to repair a used bandsaw I bought that had missing or broken parts. All parts but one were printed in PLA using 2mm walls and 2mm top and bottom layers. at at least 30% infill and 100% infill for the blade guide. The...

Programmer Cam A "Unknown Part Number" - $40 - Retail * Material: PLA or ABS * Resolution: 1.6mm * Infill Density: 30-50% * Support: Everywhere * Instructions: Remove Supports and install on machine. 8. ...Bobbin * Material: PLA or ABS * Resolution:...

This repair component was fabricated for a buddy.I've upgraded to incorporate a three-pole part, it's a hastily revised component, yet should function adequately.I've included a three-pole version featuring reinforcing fillets on all sides.The...

Following up on my Computron combiner parts set (https://www.thingiverse.com/thing:5481635), here's a full set of Technobot accessories! All the little guns and such. These are not exact 1:1 replicas, but they're close for the most part. The...

These are some parts I made to repair a used bandsaw I bought that had missing or broken parts. All parts but one were printed in PLA using 2mm walls and 2mm top and bottom layers. at at least 30% infill and 100% infill for the blade guide. The...

I have added 'v2 bandsaw height knob.stl' this version can be printed with no supports. These are some parts I made to repair a used bandsaw I bought that had missing or broken parts. All parts but one were printed in PLA using 2mm walls and 2mm top...

Initially, I intended to include the bolts in sets of 12, but after testing ABS prints, I discovered that the nut's head tends to shear from the threaded part regardless of the infill setting. This issue arises due to the larger diameter of the...

My daughter received this playset second hand, minus a few missing parts. There are a couple more pieces I plan on making, but so far I've just designed and printed the cross drill bit. Designed in blender based on measurements of the items that I...

I borrowed some design elements and common parts like switches and GT2 pulleys from the excellent Solidoodle 4 CoreXY rebuild by Elenhinan, but all of the printable parts were designed from scratch using Solidworks. I included the original files so...

There is some inconsistences in the models as these are scans, I try to do very minimal if any 3D modeling on the files because I want to keep the original look of the actual parts on these vintage toys/collectibles. I do not own this model. I am...

Button clip: I originally designed the part to have the exact specs of the original, but found the original to be too weak in some areas. After removing the weak spots and resizing a bit to account for shrinkage, this one fits really well. Results...

Replace manfrotto tripod original lower thing

I'd be happy to help you with that! ...Here's a rewritten version of the original text: Replace "Quick Release Plate" on your Manfrotto or National Geographic NG-TT-2 Tundra Tripod.

This was designed specifically to replace a broken part on 434B model monopod.3D printing not really suitable to replicate the clipping mechanism from original part, so designed for friction fit. ...At a few grams of filament will just carry a handful...

This was designed specifically to replace a broken part on 434B model monopod. 3D printing not really suitable to replicate the clipping mechanism from original part, so designed for friction fit. ...At a few grams of filament will just carry a handful...

If you have a Manfrotto tripod and you missed a leg hook, you can print a replacement Si tienes un trípode Manfrotto y perdiste el seguro de las patas puedes imprimir un repuesto

Manfrotto 055XB Mount Plate.

Manfrotto Release Plate stick

I crafted this component for use on a Manfrotto joystick after the original trigger plunger snapped off, forcing me to create a custom replacement. ...The new one functions flawlessly, saving me from having to search for an obsolete part since the...