mamiya rb67 instax back 3d models

This is a prototype mounting plate I designed to adapt a modified Instax Mini 9 into a removeable film back for Mamiya RB67's! Right now I can't offer any directions or guides on how to disassemble and modify the Instax Mini to build the Instax back...

... ...How to prepare Instax as a camera back: https://www.youtube.com/watch?v=crL5PmfyyzA.You will need some screws and light-sealing foam as well as glue.Make sure you properly align the focal plane of the camera with the film position first!Have fun!

This aid makes it clear where the boundaries are when shooting Instax Square on RB67.Printed in Polycarbonate for strength and durability.Layer height: first layer 0.2mm, succeeding layers 0.05mmTemp: 225 (Polymaker PC-MAX)Bed: 100Nozzle: 0.4mm

RB67 Focussing Knob for u/Olivares1506 on Reddit.

Framing mask for use with the Mamiya RB67 645 roll film back. Simply print and drop in over the ground glass viewfinder to aid in composing with the 6 x 4.5 aspect ratio. The little nubbins are there simply to make it easier to remove the mask from...

UPDATE: On May 19, 2020, I discovered that the original file (square corners, two slots on the back) did not work with RB accessories. To fix this issue, I uploaded a new file (rounded corners, four slots). ...This updated version has been tested with...

This is a replacement for a missing plastic badge on a Mamiya RB67 viewfinder. I spray painted it flat black and highlighted the lettering with a silver paint marker. ...The font and dimensions are not 100% correct but it looks better than nothing.

With their secure fit and easy-to-use design, you'll be able to focus on what matters most – capturing stunning images with your Mamiya RB67 camera. Whether you're a professional photographer or an enthusiast, our lens caps are an essential...

A rear lens cap for Mamiya RB67 lenses is available. This particular design won't fit the 50mm lens, which demands a deeper rear lens cap - I've also uploaded a deep cap design, though. The file "MamiyaRearLensCapF.STL" was designed with a 0.5mm...

This mask is to be placed over the ground glass to see what is in frame while shooting 35mm film in the Mamiya rb67. This may fit the rz67, but I don't have one to test (lmk if you find that it does) There are two versions, one basic version, and...

After doing some research on taking exposures longer than 1 second with the Mamiya RB67, I was presented with two choices. The first purchasing the dual threaded cable release on Ebay for ~80$ USD (at the time of writing this) or manually moving the...

After doing some research on taking exposures longer than 1 second with the Mamiya RB67, I was presented with two choices. The first purchasing the dual threaded cable release on Ebay for ~80$ USD (at the time of writing this) or manually moving the...

This is a replacement for a rear lens cap for Mamiya RB67 K/L lenses.

This part replaces the original spring element of the clip spring for the Mamiya RB67 lens caps. Before installing it, cut off the old spring (if any). ...

Unlike the Mamiya RB67 lenses, this cap is a press-in fit, engaging the inner radius of the lens mount firmly with springy fingers. It is held in place with friction and fits well on my RB67 (YMMV, depending on how you set up your printer). For a...

This a simple viewfinder mask for the mamiya RB67, if you're shooting 35mm with an adapter. It allows you to compose and also be able to do some sprocket photography (if you're into exposing the whole 35mm film). Its 1.5mm thick, so i'd advise ONLY...

... a special sequence you should follow when shooting 35mm film due to the all the lock out safety mechanisms in this brilliant camera. You'll also want to unload the film back in a dark bag and rewind the film back into the canister. ... Have fun!

Rear lens cap (flat) for RB67 lenses. I printed in PLA, but something with a little flex (like nylon) would probably work better. ...

I accomplished this by designing a 3D printed bracket for the servo motor and a hotshoe mount for the Arduino board and RF Receiver. Parts Manfrotto Baseplate Arduino Uno R3 Servo 90g Simple RF M4 Receiver - 315MHz Momentary Type Keyfob 4-Button RF...

### Components Used - Manfrotto Baseplate - Arduino Uno R3 - Servo 90g - Simple RF M4 Receiver - 315MHz Momentary Type - Keyfob 4-Button RF Remote Control - 315MHz - Arduino Uno Case (Fits tightly with lid on)...

This is the version that allows you to shoot both vertical and horizontal panoramic photos in a mamiya RB67 and a 35mm panoramic adapter. Note: ONLY FOR USE IN THE WAIST LEVEL FINDER. ...i haven't checked compatibility with other finders, so I'm not...

I had a blank focusing screen for my Mamiya RB67 and I needed one with frame lines for both 6x7 and 6x4.5 cm negative sizes so I made these templates to accurately draw them. If lines are only needed for 6x7 cm then just the 4.2 mm template is used,...

Use for mamiya universal back locking button. ... pretty lock

Non-destructive and 100% reversible modification transforms original Mamiya RB67 PRO-S 6x7 film back into 35mm panoramic frames, specifically designed for 24x68mm. If this information proves useful to you, consider making a donation of any amount.

This is a body cover for the Mamiya RB67 Pro or Pro-S. It covers the rear of the camera body when the film back is removed. The body cover is marked for easy identification. May also fit the Mamiya Pro-SD body, but this has not been tested. I...

Summary This was designed to help out a friend who had ordered some neck strap clips for his camera, but would not receive them before his trip. There were no models available at the time, so I took some measurements and modeled this. He's using a...

You can customize both the frame size and the label in the customizer. ...The uploaded STL is for 6x4.5.The mask snaps nicely into the focusing screen frame, doesn't touch the glass and won't fall out.ABS or other filament resistant to stress is...

This was designed to help out a friend who had ordered some neck strap clips for his camera, but would not receive them before his trip. There were no models available at the time, so I took some measurements and modeled this. He's using a custom...

This lens cap features later K/L design, but 2mm deeper and can be used on other lenses, such as 50mm Sekor-C with longer rear element.