mamba monster slash 4x4 3d models

This mounting box and top clamp are designed specifically for installing a Mamba X speed controller into a Traxxas Slash 2WD with a lower center of gravity chassis (LCG). First, place the ESC into the printed frame. Next, align the frame holes on...

Internal-splined half shaft for Traxxas Slash 4x4.MODEL# 6853A.

This is a ESC I used for the Makers Racing Series.Check out also ITI-FA002 (2019) 1/10th RC car

This is a ESC I used for the Makers Racing Series.Check out also ITI-FA002 (2019) 1/10th RC car

It's the measurement from the original part. ... Internal-splined half shaft for Traxxas Slash 4x4. ... MODEL# 6853A.

I wanted to install Mamba Monster Esc on Traxxas Nitro Revo for electric conversion project. ...I had to make this plate that is installed on the rear shock absorbers

The left front/rear arm is required for my Traxxas Slash 4x4 vehicle, as both the front and rear arms on this model are identical in design.

30mm fan mount for slash 4x4 slipper clutch. ... Goes on the right side of the vehicle mounts on upper right engine mount.

Mount a Traxxas Slash 4x4 Esc Mounting Plate on Any Vehicle. ...Attach Double-Sided Tape Directly to the Esc, Secure it Firmly in Place on the Plate.

Adapter plate to mount any esc to a traxxas Slash 4x4. ...Use double side tape to glue the ESC to the plate.

Mount for Castle Mamba Monster X ESC for the Traxxas Maxx, with a power switch mount. Friction fit, but use double sided tape if you want. Remixed from a mount I found on printables. ... ...

Watch it in action: https://www.meatballracing.com/slash-4x4-crawler-part-5-fenders-and-bumpers/ Secure it firmly to the differential housing using standard hardware. ...Use any 3mm button head screw that is at least 12mm long to lock the bumper in...

... ... See it in action: https://www.meatballracing.com/slash-4x4-crawler-part-5-fenders-and-bumpers/ Fasten it to the differential housing using the normal hardware. ...Any 3mm button head screw that is at least 12mm long will work to secure the bumper.

Mounts for the Castle Creations Mamba Monster X 8S and the Mamba Monster X (sensored) for the SCX6. This is meant to match up with my receiver box - includes here with switch. For the MMX8S there is both a length wise (LW) and width wise (WW)...

This mount/stabilizer holds in my Castle Mamba Monster X 8S ESC in my Typhon 6S V5. I have secured the bottom of the ESC with Genuine 3B VHB which helps with shock/vibration isolation (as well as the stabilizer being constructed of flexible PETG)...

This mount/stabilizer holds in my Castle Mamba Monster X 8S ESC in my Typhon 6S V5. I have secured the bottom of the ESC with Genuine 3B VHB which helps with shock/vibration isolation (as well as the stabilizer being constructed of flexible PETG)...

Designed in AutoCAD, this allows for dual motors on a Traxxas Slash 4x4. This been tested in ABS and I've printed them on a Tevo Tornado 3D printer. ...Some filing may be required for perfect fit.

Remixed markthemakers clamp to work on the LCG Chassis for the Slash 4x4. Also extended the depth to allow fitment of my 4s battery. Currently V2.1 further development may happen. ... Original design edited in Tinkercad

Case and mount for flysky GNSS GSM020 GPS Performance Analyzer. ...Has opening for charger port. It mounts to the rear shock tower for a Slash 4x4. Uses M3 screws and nuts to attach and clamp to rear shock tower. ...Allows for use of stock body mounts.

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more...

I crafted the Traxxas Slash 4x4 extended body mounts initially, and upon further investigation, discovered that fabricating spacers for the body mount bracket imparts significantly greater strength than the mounts I 3D printed.\r\nThese spacers...

Purchased a brand-new, pre-finished body for my Traxxas Slash 4x4 but it failed to fit properly, prompting me to modify the height of the body mounts instead. ...Following several design iterations, I ultimately settled on three distinct dimensions that...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

This switch plate is for the Castle Electronics Mamba Monster X 8S (MMX8S) esc to solidly mount the on/off switch out of the way but still in reach.The switch plate can be flipped around to multiple positions to locate the switch where you want or...

...I lost the gear cover of my Traxxas Slash 4x4 LCG... :(</p> <p>So I designed my own. It's nearly as perfect as the original piece... but different...</p> <p>Several testprints &amp; model iterations later, I had something that fits ok :)</p>...

I designed a stand specifically for my son's Traxxas Slash 4x4 1:10 scale vehicle so he could store it safely with the wheels off the ground. This setup is allegedly crucial in maintaining the round shape of the wheels and preserving the shocks and...

I've designed a custom 3D printed switch mount for my Traxxas Slash 4x4 HCG, specifically to house the brushless motor system's switch. Since it needs to be installed somewhere, I'm providing this file with installation details. To download and...

Currently, it uses a single Mamba Monster 2 motor with 2650kv, but I plan to test it with two VXL motors once I get another motor plate and maybe two more Mamba Monsters for even higher speed. This project is just a proof of concept and ideally would...

This is a control arm I modeled for a Traxxas rustler or slash 4x4. I believe it is also compatible with a rear 2wd but I haven't tested. Print horizontally, and make sure supports are on. Mirror horizontally in slicer to make a right arm. STANDARD...

This is a remix of "Akku Träger Slash 4x4 LCG" by Sani007 https://www.thingiverse.com/thing:3740043 The stock battery holders are not flexible enough. With this battery holder I can mount a big 4S pack. I added holes Version 2 : made it more flush...