mamaroo toy bar fix 3d models

Mamaroo upper toy holder

Fixing a saggy mobile on your Mamaroo baby thing requires a straightforward approach. If the female part of the socket has been damaged, this is the fix for you. First, print out the replacement piece and make sure it's oriented correctly so that the...

... the mobile mount was broken. ... I decided to make my own similar mount, since there was nothing to restore. My version consists of two parts: the first is screwed to the mamaroo, and the second is screwed instead of the original mobile mount. ...

We're dealing with a 4Moms Mamaroo mobile that's begun to sag, actually coming close enough to hit our little one right in the face. This is a well-documented problem, but unfortunately, our unit had already expired its warranty when we encountered...

After printing the original design I realized that it wouldn't fit the 2015 model which I have. The original seems to be for the 2016 model that has thinner nub piece on the mobile. I have widened the holes a little bit, because the screws I had on...

MamaRoo Gear. It is projected so that you don't get any difficulty in printing. Material PETG or NYLON. ... You get one wheel for free:))

fixed the throttle bar stl with missing one male ball joint

This repair of a Duplo part toy was urgently needed since several pieces with the same damage were found in the family. The reason for this is that small children tend to succeed in biting off parts after repeated and persistent attempts. A damaged...

I received this toy wheeled crane already broken. ...And with a little modeling and 3D printing, the toy can continue to serve other kids :) -printed with Prusament ASA -0.15mm layer height -with supports.

I received this toy wheeled crane already broken. ...And with a little modeling and 3D printing, the toy can continue to serve other kids :) -printed with Prusament ASA -0.15mm layer height -with supports. 

If your notch gets worn out on the older Mamaroo 4M-005-00 model (parts no longer made), this is the fix for you. You need to remove the old nob, predrill holes in both parts and the arm, then screw them together securely with glue holding everything...

... needed to maintain its correct alignment above the baby's head. This adapter was designed to be 1.59mm thick and slide over the mobile's end connection, then attach securely to the mamaRoo body. ...Your specific spacing requirements may vary.

Piece to fix the broken arm for the adjustable rail in the mamaRoo.

Traxxas Rustler 4x4 wheelie bar fix

Fix for Philips Blender Bar HR1363 Prefer ABS. ...Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: 0.2 Infill: 50% Filament: Surreal ABS Black Category: Household

Replacement Parts for Philips Blender Bar HR1363 Preferred Material is ABS.

You've worn down your Rock Band guitar as much as I have, causing the inside of the strum bar to develop stress fractures either in the limit stop or the magnet holder. This reinforcement insert is designed to be slotted into the middle of the strum...

... (followed by a mischievous little smiley face). It could serve as a good starting point for someone who needs to fix a toy wheel of some kind. ... The diameter is 75cm, and it printed well at this scale, taking approximately eight hours in total.

The plate is on top of the baseball sport toy.

These two parts are specifically designed to eliminate play in the steering bar of the Challenge racing rig at its connection point with the seat frame. One part is a bushing that wraps around the outside, while the other part is a plug that fits...

These two parts are designed to remove the play in the steering bar of the Challenge racing rig, where it connects to the seat frame. One part is a bushing that goes around the outside and one part is a plug that is a better fit inside the tube...

Our cat toy broke, so I decided to model the broken parts and print it. ...It's not perfect but it'll do the job!

My daughter got this toy of Bruni from Frozen 2 (https://www.amazon.com/Plush-Bruni-Salamander-Walk-Spirit/dp/B08B57VPTS) and after a short while, its foot broke and toy stopped walking. ... I've decided to try my luck at repairing it and came up with...

My wife and I bought a used Mamaroo for our son, which he loves; but, the mobile plastic is very weak and wore out. The mobile would hang down far enough to sit on his stomach, so I printed this wedge reinforcement to set it upright. Print the peg...

... me to design this wedge reinforcement to keep it upright. Print the peg and the wedge, then insert the peg into the angled portion of the wedge, followed by placing the modified wedge into the Mamaroo. ...Finally, position the mobile on top.

The armature is made from a discarded aluminum sheet, which we salvaged from our garage - initially intended as a louver for a large vent, but it happens to match the Mamaroo's aesthetic quite closely. ...In theory, any flexible metal piece could be...

My daughter got this toy of Bruni from Frozen 2 (https://www.amazon.com/Plush-Bruni-Salamander-Walk-Spirit/dp/B08B57VPTS) and after a short while, its foot broke and toy stopped walking. I've decided to try my luck at repairing it and came up with...

The armature itself is a scap piece of aluminum I had in the garage (I think it may have been a louver in a large vent) that matches the look of the Mamaroo rather well, but I suspect you could use just about any kind of bendable metal piece for...

I've found that it's difficult to find that replacement part, so I made my own. The armature itself is a scap piece of aluminum I had in the garage (I think it may have been a louver in a large vent) that matches the look of the Mamaroo rather well,...

And in the final shot, you can see our Mamaroo suspended high above the ground, its mobile attachment arm proudly bearing its weight. One crucial tip: when printing this piece, be sure to orient it sideways. If you try to rotate it during the...