male half orc fighter 3d models

Many decades later and half a world away, Sullivan learned of a lost temple of Levia from a disgraced priest. Even the quartermaster, Sullivan, was sure that a lost temple would house some extravagant booty or perhaps an artifact. Not one to let...

Especially the Body is suspect to warping due to many overhangs.Known Issues: can I fix my problem?Hammer stops half way: adjust nose of Hammer-Rotator until it can slip over the teeth of the Cylinder-Rotator.Cylinder spins over the notch, resulting...

section3 was almost missing half a former for example. Fuselage is solid now, no worries there. compiling a whole new zip file that contains ALL the edited parts. 12/26/2021: I was gonna start covering the model today, but would rather delay. I...

This character was developed by famous artist Akira Toriyama and is known to carry out a painful duty - his body guards a half of evil Hirudegarn. The author of the Tapion model went all out when working on the design of the legendary hero for 3D...

This is why I uploaded 10 versions of the design with different XY and Z clearance value combinations:0.18z 0.15xy0.18z 0.20xy0.18z 0.25xy0.18z 0.30xy0.18z 0.35xy0.36z 0.15xy0.36z 0.20xy0.36z 0.25xy0.36z 0.30xy0.36z 0.35xyEach clearance combination...

Make sure they are solid half spheres.Acrylic paint (black, white and the color of the iris)paint brush (small)10cm x 10cm mesh (I recommend fly screen)4cm x 80cm elastic band10cm round elastic band (2mm - 4mm diameter)1 roll of duct tape~1m² fur of...

If do you need to get the lock back off, the best way I found was to stick long allen keys into both of the lock's holes and then pinch them together to lever the lock slightly apart, which reduces the pressure enough that you can wedge a thin...

If you are not comfortable disassembling half your printer, this upgrade may not be for you. Familiarity the printer’s controller board is required. Familiarity with wiring and safely extending electrical component cables is also required. Improper...

The 3D printing model's chosen scale is 1/32 for FFF/FDM version and 1/64 for DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 128 parts;- A printed shuttle is 208 mm tall, 240 mm wide, 329 mm deep;- Assembly kit...

Once all four tabs are down, go back and tighten each nut about a quarter- to half-turn more, just enough to get the speaker snug. No reason to over-stress the mounting boss; the nuts should stay put, and you just need the speaker to not be vibrating...

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

Moreover, in order to conceal the places where assembly parts of the model must be connected, the figurine was cut along the contour of Thanos’ armour-plated suit’s seams. For you to receive the cleanest results possible warlord's double-bladed sword...

The shapeshifter 3D printing figurine looks as if towering above a half-destroyed city, surrounded by combined Japanese military force that barely does any harm. We are sure that this ruthless victim of the atomic bomb will be a huge representative...

The V-Core 3 uses TR8X4mm lead screws instead of the TR8x8mm used in previous machines, effectively halving the pitch of the lead screw - this means that each rotation of the motor, now moves the bed half as much. This both doubles the Z resolution...

The model’s cloak was split in half to fit even the smallest 3D printers’ build plates. All the assembly parts are provided in STL files in recommended positions that were worked out so to ensure the smoothness of the details’ surfaces after printing...

You fine tune the tension of the spring and thereby the gear pressure against the filament later but for now I find about 4-5 half turns of the screw is good. You can use the original thumb screw instead if you like.At this point you can also install...

Probably about half a meter of 20x40 extra should cover it. This is the extruder it's designed to use, but you could use the standard D-bot CoreXY bowden if you wanted to. Just be sure to print the right mounting plate for the X carriage. The...

The assembly takes about half an hour.Designed with Autodesk Fusion 360All parts are designed to be printed without material supports ### Parts to be printed - The main body (choose the model corresponding to your hotend : E3Dv6 or XCR-BP6) - The...

With the same purpose, Shellder that is commonly attached to Slowbro’s tail was divided in half and its spiral shell is now also provided separately. All assembly parts are provided in STL files in recommended positions that were worked out so to...

That is not the half of it. Oh, no. Oh, my. They're all wilting. Doesn't look very good, does it? No. And whose fault do you think that is? You know, I'm gonna guess bees. Bees? Specifically,...

#### Optional Lastly, if you want an extension with rollers for longer prints, you can print out additional YExtension's, YExtensionSupport's (4 for each extension, go on the bottom half), and UpdatedYIdler's/UpdatedAxle's (as many as you'd like...

They are a few, old, male, Victorian Era English astronauts. They live in small towns and use other folks as servants.</li> <li><b>Zealots</b>. <i>Homo sapiens</i>. An ultra religious, Medieval Age civilisation (or just a town?). They use Hams as...

Its origins are vague, but its "ancestors can be found on Neolithic pottery as well as Bronze Age ritual vessels."[38] A number of popular stories deal with the rearing of dragons.[39] The Zuo zhuan, which was probably written during the Warring...

Motorized Solder DispenserThis project was created a year and a half ago. I printed it, but I have not collected it until today, somehow everything was not up to it. Yes, and there are many other projects that are unfinished, which I am gradually...

At least half of the problem of memory organization appears to reside in the storage procedure. Most of the remainder seems to be wrapped up in the problem of pattern recognition within the storage mechanism or medium. Detailed discussion of these...

mostly black or white, plus orange for one half of the filament release. So, it kinda bore a vague resemblance to the bird, if you squint at it just right. Plus, I'm also a strong supporter of open source software, especially on Linux. Since that OS...

This happens every time the Z-axis shafts stop rotating after two and a half seconds. And do not worry about the memory resource (read / write), although the Arduino claims one hundred thousand cycles, but I implemented this process in such a way...

This is brief, in more detail in the video.The basic parameters of the module can be read on the seller's page, and there are many reviews on YouTube.Of course, if I had done this device not on camera, everything would have gone quickly and smoothly,...

Apparently the rotor stops in a position where it has, so to speak, a half-dead magnetic field (I think so, maybe I’m wrong) ... But in principle it works ... But sometimes you have to start by turning the rotor, and this is inconvenient, of course,...

2021/9/30: The forehead half model was missing its details. I have corrected this. Additionally, I split the original 'MCOR Helmet Skull Cap.stl' file up so that the dome portion is now separate from the side panel. This makes this piece easier to...