makers tool works 3d models

Stone_floor_1............................2216 polygon, a stunning work blending structure with harmony to define both function and artistry in stone laying craftsmanship. ..................................................1110 vertices come together...

NOTES: • This setup I printed using PETG (but PLA and ABS work fine). <br /> • I printed it at 240C with a bed temp of 85C. <br /> • I used the original extruder stepper motor, but I'm honestly, not crazy about the weight it puts on the whole...

I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. Just remember to leave enough time for the glue to set before combining too many parts. 3 - All parts should fit together quite well,...

Deep in the heart of the wood Madam Wilumbra works her druidic witch magick, twisting the forces of Nature herself into foul creations with one sole purpose: exacting vengeance on the humans and retaking the lands for new growth. Each day she...

This method is the easiest to set up and, in my opinion, the one that works best.It's important to state, that not all models are compatible with each other. The compatible ones are listed here referring to their file names:</p><ul><li>“thin...

Using his popularity and influence, Grommash created the Iron Horde free association of orcs who could decide his own destiny.All assembly parts of the FFF/FDM versions come in STL files in recommended positions that were worked out in order to...

Fortunately, you are probably making this to work with an MMU, so you can always use dissolvable supports. :D First, print the parts. I'd recommend ABS+ for the main support. PLA will probably do as well, but a bit of flex is a good thing for that...

Gyroid infill is as good as solid infill for transmitting these shear forces, so that is what I used to save material.With Prusa's powder-coated sheet (which has trouble adhering to PLA), one of the footpad disks lifted off the build surface during...

&nbsp;3D Gloop covers the middle ground for me and really works wonders. &nbsp;It leaves enough time to set, so parts can be positioned correctly and it dries fast enough to hold awkward parts without the need for taping. &nbsp;I used the PLA version...

Also works with a slight loss of appearance. But my recommendation is therefore with support structure. With the built-in housing, I only used a manual support structure that I positioned by the large fan hole. Attention: The conversion is done at...

8 ohms would work too. The 15 watts are quite oversized. 5V and 10 ohms result in a current of 0.5 amps and thus a power loss of 2.5 watts. But the higher value won't get that hot. Sorry, but I don't get a Remix entered. This laboratory power...

Anyway, as I said, this is not the definitive solution at all, so I am designing another piece that will work for this case as well as for many others. I'm sure it will be useful. When I have it done and upload it I will leave the link here. I...

If you watch the video, This Old Tony does a great job explaining how the Vice works and showing off the unique mechanism that allows the Vice to function. My model is not a replica, and is designed from the ground up to be 3D Printed. Some...

It is essential the the slots are formed in the same spot on each rod, which is why the marking jig was used in the previous step.There are two other stabilizing jigs provided, both have a flat surface on the bottom, which allows you to hold the...

I work full time, so only have a few hours a week to improve / update the design... but fully intend to keep doing so :). Future thoughts? * Upgrading to include ROS (currently using my very amateur Python code). * Single power supply...

###If you like my work, you can support me through Patreon: https://www.patreon.com/gigapenguin3dprints/posts ###Compiled RAR file is available in download section! Description ==================== A small showroom that fits up to 4 1/64 scale...

Cad cart 1 is the ultimate one-stop-shop solution for creating stunning CAD, rendering, video, 360-view, catalogue and model-view designs for exquisite diamond jewelry creations.\n\nOur expert team provides top-notch CAD files for an extensive range...

The SI2301 P-MOSFET works in a very twisted way. Gate is connected to input with a 2M2 resistor in series. The SRV5-4 diode array protects it. The source is grounded, the drain gets a small (100mV) positive voltage. The internal diode does not open...

For a low-speed pullcopter or boat propellers, a pitch of at least 2×ArcRadius works well.Blade shapeThe next 3 parameters determine the chord of the airfoil at any point along the blade length. The chord of the airfoil, tilted by the angle of attack...

I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. Just remember to leave enough time for the glue to set before combining too many parts.</p><p>3 - All parts should fit together quite well,...

The printed structure could be accomplished with one or multiple rovers working in unison and alignment markers on three or four corners along with their rate sensors and accelerometers for precision building. As the rover lays each layer, only...

This is a completely new version of my original design (here: https://www.printables.com/model/145632-dslr-rig) without the cage and with fewer parts.&nbsp;Redesigned in SOLIDWORKS for higher precision.You will also need:15 mm aluminum or carbon rods...

This will also work with the 35mm version.Install InstructionsIf using a BLtouch.a. Attach the BLtouch to the mount with the ribbon connector facing towards the back of the printer using (red) 2 x M3x16 and 2 x M3 Hex nuts</p><p>b. Connect the...

It works best to print the end caps with different colors that will make it easier to identify the start and the end of the maze. The flippers keep people from rolling the ball back into the maze from the center. One side of the flipper mount is...

This is a Core XY conversion kit for the Ender 5 with Linear rails There is a MK2 version here:https://www.thingiverse.com/thing:4777606 Big shout out to Scott3D for his fabulous work on the Hypercube Evo which I have taken the belt tensioner detail...

HISTORY OF DEMONThe author's work is performed in the form of a vampire demon. Great for fans of the Blade series, Constantine and other related monsters. The model was created in ZBrush.ABOUT THIS 3D MINIATUREThe model is saved in STL files, a...

PETG and ABS are best if your bike is subjected to high temperatures (like sitting in a car on a hot day) but any of the materials should work. No supports are needed, and you can use whatever layer height you wish. I suggest using enough shells to...

We can use such representations: 1) Use each edge layer or face position which we are going to be working off as reference value for vertical rotation at `Port # n`. ```(Position) n == (C*P)(Face P#)(L)* = corner extrusion design in port C Corner...

I had no problem with these files, but you can also download the fusion 360 file and create the .dxf from this file in case something doesn't work out for you.Attachmentsticketholder.aitopbottom.dxfmiddle.dxfGlue Bottom and Middle Part&nbsp;&nbsp;Now...

I have 'fat fingers' and a shaky hand, so the sticky glue works out best for me, especially with small pieces. Just remember to leave enough time for the glue to set before combining too many parts. 3 - All parts should fit together quite well, do...