makergear m2 simplify 3d optimized profiles

This light bar was created to mount LEDs and brighten my MakerGear M2's bed. Fastened with double-sided tape on the X axis support, it runs on 3 AA batteries illuminating 6 LEDs. Customize its length or number of LEDs using OpenSCAD or the Customizer...

The original MakerGear M2 Filament Drive file on Github has been enhanced by adding a support tube at the top, which fits snugly when pushed in place. The filament guide tube size was increased by 2% to account for nylon shrinkage upon solid printing...

A spool holder mount for a Makergear M2 printer for[this nice design](https://www.thingiverse.com/thing:1805648). ... I couldn't find a long enough M8 screw, so I used a 8mm treaded rod and a M8 nut as a replacement.

My organization has an older MakerGear M2 printer which uses a different type of limit switch holder for the Z axis than on newer ones. After the old one broke and I couldn't find the stl anywhere online, I chose to model it myself. ...This one isn't...

This is a new SD card holder for the Makergear M2, inspired by the original "Another SD card holder." A big thanks to sgrover for the initial design, while this creation marks my first contribution. ...Special appreciation to Jason for allowing its use...

This is a simple, straightforward fan shroud designed specifically for the Single V4 extruder found on a Makergear M2 system. To install this fan shroud, first mount the larger fan onto it using four M3 x 16 screws. ...If needed, tap holes are present;...

Here is a simple fan shroud for the Single V4 extruder on a Makergear M2. Instructions: Mount the larger fan to the fan shroud using (4) M3 x 16 screws. ...You can either drill pilot holes or simply force the screws in, allowing them to self-tap into...

This bracket lets a $6 webcam fit very discreetly on a MakerGear M2 to offer a low-resolution live video feed of the part being printed in real-time. There are two versions available. ...The original (black, part.stl) version needs to be secured with...

With this mount, you can easily attach a Raspberry Pi camera to the bed of your MakerGear M2. Perfect for use with an OctoPi setup. The arm is adapted from a design found at thing:2267182 on Thingiverse, while the camera case comes from...

My company relies on an outdated MakerGear M2 printer that employs a unique limit switch holder for its Z axis, distinct from those used in newer models. When the old part failed and couldn't be sourced online, I decided to create a digital model of...

... *SE_Cooling_Duct.STL created by "Makergear", all rights and attributions for the 3D model go to Makergear.* Test Results I don't know if this is an accurate test but I just tried to print some 1.5" tiny cones (1 at a time) to see what would happen.

A BLTouch adapter plate designed specifically for MakerGear M2 Rev G and ANTCLABS BLTouch V3.1(#ad). This design is part of my SKR 2 mod for MakerGear M2 Rev G. The M2 has been the absolute workhorse for me and I love it very much ever since I got it...

I remixed this from my previous MakerGear M2 C270 mount for the bed. I made it for my MakerGear M2 Rev G purchased in 2019. I decided to move the webcam mount out from the bed to the printer chassis because I'm planning on modding my M2 with SKR2 and...

Print Settings Printer Brand: MakerGear Printer: M2 Rafts: No Supports: Yes Resolution: 0.2mm layer thickness Infill percentage: 35% Notes: The housing parts were printed at a resolution of 0.2mm, while the knob was manufactured at a heightened...

The Makergear M2 tool and tape holder is a highly versatile accessory designed to maximize your productivity when working on projects that require precision and accuracy. This innovative holder attaches securely to the M2's robust frame, providing...

Print Settings: Printer Brand: MakerGear Printer: MakerGear M2 Rafts: No Supports: No Resolution: .2mm layer height Infill: 100% Notes: This part may be slightly off by a fraction of a mm from the original, but it works well once screwed into place....

This bracket was designed to provide strain relief for Makergear M2 heated bed wires, which on older models flex continuously during printing and cause the wires to break. It attaches to the spider using 20mm M3 screws that fit into the existing...

... with more clearance, a better clasp, and improved printing flat. If you print and like them, please post your photos! Print Settings: Printer Brand: MakerGear Printer Model: M2 Rafts: No Supports: Yes Resolution: Fine Infill: 30% Notes: Print flat

I remixed a C270 mount for my MakerGear M2 Rev G. It replaces one of the bed corners. I've been rocking this setup with a magnetic bed and it's been working nicely. The webcam view is great! Since it moves along with the bed, its view of the print is...

The Makergear M2's fan tapped the frame when homing the X axis, disrupting my feng shui; however, a simple fix was to rotate the fan slightly. To maintain a square fan position while moving it over a few millimeters, use this bracket designed for...

I designed another tool holder for my Makergear M2 because I utilize a Sealed Filament Tub on the left side of my printer. The standard tool holders available on Thingiverse were unsuitable due to this, so I developed one that suits my needs. This...

I've redesigned the MakerGear M2's filament drive system, incorporating a direct connector for seamless integration with the Mosaic Palette. This eliminates the need for the vendor-supplied velcro attachment and allows users to securely insert the...

The Makergear M2 features hard end stops for X and Y axes; however, the Z-axis can potentially push past its switch, disrupting Z adjustments. To rectify this issue, print a part that attaches to the Z-axis guide rod as a stop measure. I printed mine...

Another tool holder designed specifically for the Makergear M2. Since I already have a Sealed Filament Tub on the left side of my printer, I needed an alternative to the existing Thingiverse tool holder, so I created this one instead. It securely...

This is a custom drawing attachment designed specifically for the Makergear M2 Printer.\r\nFirst, A Word of Caution........\r\nPlease note that this is an experimental design still in development (I'm posting it here at your request). This attachment...

I engineered this housing as an electrical controller for maintenance LED strip lights fastened to the right hand Z-stage frame of my MakerGear M2 printer. The illumination system supplies lighting for lubricating and cleaning the z-axis mechanism,...

Printer Brand: MakerGear Printer: MakerGear M2 Rafts: Doesn't Matter Supports: No Resolution: 0.150 Infill: 20% Notes: I rotated the print 30 degrees along the x-axis (so the flat extruder-facing side touches the build plate) and added a 1-layer...

This is a modified spring loaded hinged version of the original V4 Filament Drive for the Makergear M2. My original drive (printed in PETG) wore out (the springiness of the tension of the bottom of the drive) so I designed this hinged version to...

... millimeter screws. You can also watch my Youtube video covering my various Makergear M2 Mods here: https://youtu.be/jD6ZTcCd0j8. ...If you are looking for more of my DIY content then check out http://www.easybotics.com/ and http://hilo90mhz.com/.

... 100% infill if I want to color in between the lines. (the skull pictures shows with and with out infill.) That's all I have time/motivation for right now...... Print Settings Printer Brand: MakerGear Printer: M2 Category: 3D Printer Accessories