makergear m2 enclosure for rambo board and viki lcd 3d models

... 213 VC-3, which is a non-drying thread locker. Optical Endstop: http://www.thingiverse.com/thing:1195834 Youtube video covering my various Makergear M2 mods: https://youtu.be/jD6ZTcCd0j8 By - http://www.easybotics.com And - http://hilo90mhz.com

To make this long explanation a little shorter what I did was: • Removed the standoffs for the Printerboard used in the original and added stand-offs for the RAMBO board. That meant new stand-offs and holes. • I added a hole in the top for the RAMBO...

A new version of this part has been printed using a 3D printer, specifically the MakerGear M2 model. The newly printed knob must be installed, followed by pressing it firmly into place to secure the collar. ...This 5/16 collar fits tightly over the...

These pieces of hardware make this bracket: http://www.thingiverse.com/thing:62443 easier to securely fasten onto a MakerGear M2 printer by attaching it firmly to this tool holder: http://www.thingiverse.com/thing:198825 Instructions: I drilled holes...

Makergear M2 Single V4 Extruder Fan Shroud Upgrade for Enhanced Performance and Reduced Noise

I have successfully upgraded my Makergear M2 from the 3Vb to the V4 hotend and had to create this new extruder mod for soft materials to work with my M2. I recently installed it and am currently conducting thorough testing at this time. So far,...

Save four screws that attached the RAMBo to the M2 frame and use those to screw down the printed adapter rails. The rail with an indent goes on the right side to avoid a protrusion blocking the rail. Use four 8mm M3 screws to secure your Duet to...

When you upgrade with the dual extruder kit for the Makergear M2, swap out the X axis belt clamp immediately. The factory setup automatically places your X home position roughly 5 millimeters shy of the bed's left edge. To make more efficient use of...

This enclosure houses stock ender 3 LCD and motherboard (and all other similar motherboard screw patterns). LCD is mounted using original ender LCD mount. Motherboard is mounted by screwing the motherboard on the enclosure tray. Enclosure comes...

There was a lack of a fan mount which I feel is a vital port especially if you use your printer in and enclosure or use stepper drivers not built into the board. I added the option for fan mounts on the top panel and aslo the port for the standard 2...

This is a Control case for the V1 LowRider2 CNC. ... Primarily built around the SKR 1.2 pro control board and BTT TFT35 E3 LCD screen that V1Engineering sell. Fits on the Y plate and houses all the electronics. ...

The base piece is held to the MakerGear frame with a single M3 screw, one washer, and one Nylok nut. The VESA mount is secured to the RasPi case with four 3mm screws and Nylok nuts. I printed the mounting post (base) in ABS and the X-shaped part in...

5) Added Einsy-RAMBo / Mini-RAMBo / Retro-RAMBo Plate-Cover, will work with any RAMBo that has 95mm x 61mm mounting hole spacing, I recommend using the deeper housing 39mm for the RAMBo's. This will eventually be a Universal case for the original...

... drivers not built into the board. To address this, I added the option for fan mounts on the top panel and also included a port for the standard 2-connector LCD controller. ...The customizer options were reorganized in tabs to improve navigation.

... in Configuration_adv.H. Additionally, you'll have to add a pin definition to the Pins.H file (pins_RAMBO.h for me), as my printer runs on a RAMBo 1.3 and I used the Z max endstop connection. ...The line I added was "#define FIL_RUNOUT_PIN 30".

Since I'm just 13, I had limited materials at hand, so I headed to Walmart and picked up some foam boards, figuring that if they're used for insulation, they'd make great enclosure material - especially since each one cost only about three bucks! To...

To achieve precise leveling of the bed on a Makergear M2, utilize this dedicated dial indicator mount specifically designed for use with the V4 extruder. ... First, remove your current filament drive and then securely attach this precision leveling...

Functioning seamlessly and smoothly, this hot end delivers high-quality prints, while its durability promises longevity. The red printed washer (above the white ceramic hot end in the image) is used for adaptation purposes. ...Remember to print your...

This profile includes fine-tuned settings for ABS, PLA, PETG, Nylon, and PC materials after hundreds or dozens of hours of refined printing experience. Requires Simplify3D to work efficiently. A crucial step before printing involves conducting an...

This model is parametric and can be modified in Inventor if modifications are needed to the nub diameter or design. The split opening acts as a spring and supports the nozzle further. I had to use a vise to secure the plastic while threading into...

Ideally you should do an extrusion-width test with your exact nozzles and then edit the text file to change the extrusion multiplier. You can't make changes to these settings and then export them from Simplify as it will corrupt the multiple...

The model is printed in PLA and it works well.

The solution was achieved through a combination of threading an M4 x 35mm Hex cap screw into place from beneath and carefully pairing it with the complementary M4 hex nut along with the included thumbscrew. ...This innovative approach now renders...

Remove the two lower machine screws that secure the filament drive body to the extruder motor and bolt it on top of the filament drive. I utilize the bed leveling wizard, setting zero on the dial at the center of the bed plate. Then, I take...

Customized version of https://www.thingiverse.com/thing:45101 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=45101 Using the following options: spool width = 58 units filament diameter = 2...

Found an optical mount lying around but couldn't locate the sensor initially. Every single one available on Amazon came with a horizontal design, which prompted me to whip up this makeshift solution in no time. ...I made a critical oversight by...

RAMBo board inverted.It can't attach the Raspberry Pi directly to the enclosure.It also reinforces the frame.It prevents the sleeve of the extruder cable from slipping out.See my blog for more information. ...(it's Japanese)</p><p>&nbsp;</p><h3>Print...

This is an enclosure for a four-button-board as one can get very cheaply on Aliexpress, eg. here: https://de.aliexpress.com/item/32281455411.html?spm=a2g0s.9042311.0.0.fe884c4dpv9QEZ Print without supports, you won't get them out of the inner part of...

Next, I fastened the enclosure directly to the PICA board using M3 8mm hex screws and a matching hex nut. I routed the wires through a large circular hole. Special thanks go to mjrice for designing the original components and the Wilson II. ... Print...