makerbot printshop 3d models

-mike- Instructions: I printed all the parts of the puzzle, using PLA Filament, on a MakerBot Replicator 5th Gen Printer using the following settings: Layer Height=0.20mm, Shells=2, Roof=.80mm, Floor=0.80mm, Fill=10%, Infill Pattern=Diamond (fast),...

I would recommend printing the RGS Adapter 20.95 mm before the 21.05 mm version. Note: At time of upload, the design has not been tested in competition and has no guarantee of performance. Print Settings Printer Brand: MakerBot Printer: MakerBot...

Please also note that, with these stabilizers installed, I usually run 0.10mm Z-Offset (set in MakerBot Desktop) as this marginally increases the print bed nozzle spacing in case the Stabilizer adjustment is a fraction tight. In addition, I often...

Print Settings: Printer Brand: MakerBot Print Method: MakerBot Replicator 2 Rafts Used: Yes Supports Required: No Resolution Achieved: 0.2mm Infused Density Achieved: 10% Infill I printed my stand using the Makerware software, which gave me 10%...

Use cautiously as this may led to stripped or otherwise damaged gears in the OWI-535. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 1 Rafts: No Supports: No Resolution: .2 Infill: See Notes Notes: As Pictured: Alpha - Outers: .2...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: No Resolution: .2mm layer height in model, but any is fine. Infill: 100% in model, but any is fine; may affect durability. Notes: To print with no supports,...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: Yes Custom Section Project Guidelines Overview and Background Students will design their own serpent-like antagonists based on the stories they have read in...

https://youtu.be/58YBYkTr3eM UPDATE 2017.02.02 This project has evolved into http://www.thingiverse.com/thing:2081258 Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Z18 Rafts: Yes Supports: No Resolution: High Infill: 0% Notes:...

Print Settings: Printer Brand: MakerBot Printer Model: MakerBot Replicator 2 Rafts: No Supports: No Resolution: Standard Infill: 10% Notes: Original model scaled up to 110 percent for a half-inch section of EMT conduit. For an adult-sized staff,...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Rafts: Yes Supports: No Resolution: standard Infill: 10% How I Designed This I measured the circumference of my pointer and ring fingers, then used the formula to get the diameters...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: Yes Supports: Yes Infill: 10% Post-Printing Instructions Handheld Cringe Device (pictured first): The shape of the handle was altered from jbbarlow’s design:...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2 Rafts: No Supports: Yes Resolution: 0.200 Infill: 20% Notes: I used a Rep 2 to print all the parts except the stand, which is too big. I used a DeltaMaker for the stand. If you...

Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator (5th Generation) Rafts: Yes Supports: No Standards Overview and Background Project: Rain Rain Everywhere Through this lesson, students will find a location for 2 rain gauges,...

The design of this toy was inspired by Theo Jansen's Strandbeest creatures, and combines 3D printing with some custom hardware to put the beauty of Jansen's walking mechanism in your hands. Kits are available for purchase here:...

Far more accurate and less clunky than its counterpart.\n\nPrint Settings\nPrinter Brand: \n MakerBot\n \n Printer: \n MakerBot Replicator 2\n \n Resolution: \n Not relevant to the project's performance.\n \n Infill: \n Set at 20% for increased...

Please also note that, with these Stabilizers installed, I usually run 0.10mm Z-Offset (set in MakerBot Desktop) as this marginally increases the print bed nozzle spacing in case the Stabilizer adjustment is a fraction tight. In addition, I often...

You can see it here: https://www.youtube.com/watch?v=Hk5leLENccE Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator Rafts: No Supports: Yes Resolution: .2 Infill: 5% Notes: Print one of each part except for the clip (you'll need...

Print Settings MakerBot Replicator (5th Generation) was used with settings that included supports and rafts. Post-Printing Testing the Anemometers After creating and printing their anemometers, students took them outside to test their spinning...

Although this was not created using the MakerBot Customizer, this is a custom part. Enjoy this enclosure for a temperature and humidity sensor that I built for my home automation setup. The sensor is built using an EasyNewbie PCB created by...

... You also get two extra logos: the Makerbot one and a blank one, allowing you to customize your box even further! As for print time, it depends on how big your printer is. If it's big enough to hold all 10 parts, it'll take about 5 hours to finish.

Open your model in a program capable of reading STL files (for example, Meshlab, Makerbot, or Meshmixer) or upload it to service companies like Shapeways.com or Viewstl.com. 3D Print Your Model Use your model to communicate with others about a...

Next, I adjusted it using Shift+click to 120x120mm so that the thing would be large enough to use and fit on various printers including MakerBots. Next, I used alt+click to make another triangle. Then, I re-sized it using shift+click to 110mm and...

for Makerbot Replicator): 0.2 mm layers PLA - no raft (as raft difficult to remove) ABS - with raft (to minimise warping) Installation Instructions Install the points (turnout) on the roadbed and cut a hole or slot for the spring steel wire as per...

So it should be printable on many printers which are limited to 150mm along the y-axis (various makerbot clones for example). Use the NoBorders-files only if you're limited by build volume. <b>Update for a 3rd module displaying seconds</b> If you...

Once the designs are complete, they save them as STL files and print all the parts using a MakerBot Replicator 2 printer. After printing, the students assemble the engine and test its functionality. This process often requires reworking and...

Fair warning: The numerals on the cubes can be a bit of a bear to get into place, but the result is outstanding. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20 Filament: Zhoupu,...

Use the following link instead to launch the customizer:[OPEN THE CUSTOMIZER](https://customizer.makerbot.com/things/3867358) This is a customizer for creating LEGO-compatible rectangular bricks with text engraved on all four sides. You can also use...

My Shape Designs Can Be Easily Printed With Little Plastic I Made These Simple And Intuitive Design For Anyone To Resize As Needed Quickly Print Settings Printer: CraftBot Rafts: No Supports: No Resolution: Optimum Infill: 30% Square Notes: This...

Next, I adjusted it using Shift+click until the long side was approximately 120mm so that the thing would be large enough and fit on various printers including MakerBots. Next, I used alt+click to make another heart. Then I resized it using...

Next, I adjusted it using Shift+click to 120x120mm so that the thing would be large enough to use and fit on various printers, including MakerBots. Then, I used alt+click to create another triangle. I resized it using shift+click to 110mm and moved...