maker select v2 glass bed 3d models

I reworked my print of the original design to better fit my v2 printer and a thicker glass. The revised version is now .2mm taller and .4mm thicker along the z-axis. ...To accommodate these changes, I added clips on the back of the z-axis carriage,...

Easy to read. ...These inserts fit snugly over standard leveling knobs found on many machines, including the Make Select Plus. ...By adding approximately 2mm in diameter all around, they make it effortless to turn and adjust the knobs with precision.

This camera mount is designed to attach the the Monoprice Maker Select V2's base plate and slide back and forth without interfering with the print bed. The rotating base and arms used where sourced from here. ... Category: 3D Printing

After adding a glass bed and upgrading the thicker aluminum Y carriage on my Monoprice Maker Select v2, I discovered that the thumb screws remained loose after adjusting the Z end-stop. To address this issue, I decided to upgrade the springs for...

I designed a thumb screw cover for the bed leveling wingnuts that come with the Maker Select v2 from Monoprice, using what I had on hand since I didn't have any extra M3 nuts. The stock thumb screws fit perfectly into this print with my printer's...

This 3D printed camera mount is engineered to seamlessly attach itself to the Monoprice Maker Select V2's sturdy base plate, effortlessly gliding back and forth without compromising the print bed in any way. ...The ingenious rotating base and arms were...

I crafted a filament guide tailored specifically for a spool that's mounted directly on the Maker Select V2.1 printer.

The Creator Stand is a compact attachment that plugs directly into the Maker Select V2 Control Panel, designed to securely store both the supplied Spatula Tool and Diagonal Wire Cutters.

I crafted this adapter specifically to advance the gantry on my Monoprice Maker Select V2 following an upgrade to the 4mm Y carriage sourced directly from RepRap Champion, a reputable supplier on Amazon.

Adapter for Mounting Cobra Fan Duct on Maker Select v2.1 Printer Based on raymnli's design, I had to make some adjustments to accommodate changes in the X-Axis bearing brackets of my Maker Select v2.1 printer. The new brackets have a raised middle...

I purchased a Maker Select v2 in September of 2017 and immediately disliked the loose y-axis wiring that seemed to hang precariously, waiting to be pinched between the table and frame. I discovered a cable chain designed for a Wanaho printer here (a...

Monoprice Maker Select v2 Mosfet Mount. This mounting bracket is designed for installation alongside the Melzi board. The holes on the board are spacious enough to cover the Melzi board's mount screw base. ...To ensure a secure fit, attach the bracket...

I'm trying to eliminate the cumbersome enclosure from my Maker Select V2, but none of the available PSU boxes on Thingiverse are compatible with the Mean Well LRS-200, so I've opted to design a custom one that's lightweight and meets my specific...

Modeled after stock cooling duct on Monoprice Select v2.

(And thanks to Dabeach for the original design) Print Settings Printer: Monoprice Maker Select V2 (Possibly the Wanhao Duplicator I3 V2.1) Rafts: No Supports: Yes Resolution: 0.20 Infill: 20-30% Notes: Comment for any suggestions, please! Oh and I...

Print Settings Printer: Maker Select v2.1 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Notes: Be sure to use supports to keep the cutout for the fan duct from sagging. How I Designed This =================== Rebuilt raymnli's mounting...

This is a protective shield for the print head cooling fans on the Monoprice Maker Select V2, designed using Autodesk Inventor Professional 2016. Theoretically, this design should also be compatible with the Wanhao Duplicator i3/Cocoon Create, but I...

I aimed to lift my maker select V2 control box off its screws at the underside and onto some feet by designing this cradle that fits snugly around the bottom of the box, providing it with a better resting place. You'll need to print two of them using...

I Added the MOSFET Mod to My Maker Select V2. Two Magnets Hold it in Place, Covered with Electrical Tape. Don't Be Like Me - Skimp on the MOSFET Mod at Your Own Risk! You Think You're Safe Printing PLA, But That Hotbed Temperature is a Hazard...

I designed a clip to keep my glass bed firmly in place on my MP Select Mini V2. My bed was approximately 4mm thick with the glass bed and Buildtak installed. The clip's mouth has ridges to provide a firm grip, which worked well to hold down my glass...

I wanted to try a Y axis mounted camera for my Maker Select V2. I had the "Raspberry Pi Camera Case and Mount for Mini Kossel" already printed out but I didnt like how flimsy it's mounting arms and back were so I drew this up and mounted it to the Y...

To control the fan speed on my Maker Select, I use M106, and to be safe, I default the "Laser Power" to 10 (S10). That way, I can check the laser path to align the item and ensure nothing will be damaged accidentally. Then, using a text editor, I...

Manufactured after high-performance heat dissipation channels on the elite Monoprice Select V2.

I bought a used Monoprice Maker Select V2 3D printer and noticed it was missing the filament cooling fan and shroud/mount. I looked on here and couldn't find one, so I made one (the light blue part in the attached picture). Figured if anybody else...

... Print Settings Printer: Maker Select V2 Rafts: No Supports: No Resolution: 0.2 mm Infill: 25% Notes: I printed this design using PETG with a slow setting for the outer layer to achieve an extremely smooth surface, facilitating easy spool-sliding.

I really liked grommel's spool holder, but I have a Maker Select v2 with different mounting hole placement than the i3 plus and I didn't have the larger bearings used in that design. Modifications to the original design include: - Relocated...

I needed an easy-to-remove yet secure mount for my borosilicate glass bed on my MP Select Mini equipped with the 4th Dimension Modifications 120x250mm extended bed. I had the borosilicate glass custom cut to a size of 5 1/8" x 10 1/8". The brackets...

A while back, there was a surge in interest for external 120MM fan shrouds specifically designed for the Maker Select V2. The stock 40mm fan was not doing its job and was actually pulling air in instead of pushing it out. I liked the idea of using a...

I'm excited to show off my Monoprice Maker Select V2, which boasts an impressive array of mods that significantly enhance its performance. Among the notable upgrades are the z-brace mod, the Dii Cooler mod, and my own innovative Smooth Spool Holder...

--- I'm fed up with disassembling the extruder on my Maker Select V2 and watching those tiny black heatsink spacers fall out and roll away. It's a constant hassle. No more. To solve this problem, I designed a single-piece spacer that performs its...