maker select v2 glass bed 3d models

Thanks, Jae Print Settings: Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Infill: 75% Notes: To assemble this bracket, use 5mm M3 Cap bolts to screw it directly into the Meanwell NES-350. ...Then, secure the bracket to...

Print Settings: Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: No Infill: 75% Notes: This bracket is designed to utilize M3 cap bolts, which screw directly into the bracket and secure it to the bottom plate. The holes are...

I wanted to increase the setup repeatability of my printer and the easiest way to do this is to add a BLTouch or similar sensor to allow the use of mesh bed leveling. This is a remix/redesign of thing: 3635758 with my LED light bar thing: 2640410...

Another crucial step in achieving flawless prints: ensuring your print bed is perfectly square. If it's not, you're essentially printing diamonds rather than squares - albeit with a subtle difference (check out Prusa Mesh Leveling on YouTube for more...

This series will kick off a development of my Wanhao Duplicator i3 v2.1. This episode will push the X-Axis holding frame both 30mm wider and the bridge 30mm higher to allow further advancements. Azza's Z-Brace will be supported throughout this...

... twist and cause drag. Then reassemble the rest of the printer. Now, you should notice that your four springs have almost equal compression to them, which will result in far less bed relevels - even with the stock thumb wheels (which I still use).

Remixing a dual-object setup is key - one part will securely fasten to the side of your printer, while another will neatly house all your tools. ...To achieve optimal outcomes, I recommend printing the design inverted, with strategically placed support...

I was really impressed by the design of that flexion thing over on Thingiverse - https://www.thingiverse.com/thing:3825972. However, I thought the shroud was a bit too low, so I combined it with an air assist I got for my laser, which you can find...

This setup is meant to be installed snugly right behind the screen board within your MSV2. The pre-drilled mounting holes for the MOSFET board are precisely designed for M3x0.5 stand-off screws. ...If nylon hardware is being used, you may need to tap...

Simple Mounting Bracket for LED Lights Around Printer. ...The lights featured in this setup can be found at Amazon, listed under the product code B077B292R7.

My attempt at a smoother sliding spool holder... I'm not actually sure if it's any better. ...My filament doesn't always quite sit perfectly straight on it (slides into the valleys), but it seems to spin even more smoothly that way.

Remix of https://www.thingiverse.com/thing:2917820 by ELCorbo and https://www.thingiverse.com/thing:2618158 by patprints. Basically a shorter bracket for the MKS Mosfet. ...

I designed this to work seamlessly with my Flexion extruders, making it a possibility that it might not function as intended with the stock hotend. Print it using a heat-resistant material, but given its distance from the heater block, using PLA may...

You'll require extended fasteners to secure a bigger reel of material safely. ...Position this component strategically between the spool holder and the frame, then screw it in place to support larger-diameter filament rolls effectively.

I enjoyed this mod, but for my precise requirements, I needed it slightly smaller in some regions and larger in others. Specifically: * The square tube now fits snugly into its original stock holder. * The original pin now sits flush against the...

I'm a perfectionist when it comes to my machine, so when my wife mentioned the brightness of the screen the other night, I decided it was time to take action. Maybe she was right - it might be too bright for comfortable viewing. ...So, I installed a...

UPDATE: A Rev2 Corner Foot has been added. It's been beefed up a little, the side tab has been widened, and side frame rail now rests in the bottom of the tab. The printer needed some feet. Just something to get in between the metal frame and the...

This thing was designed with Tinkercad. Edit it online at https://www.tinkercad.com/things/lNFAubpxxFy. I needed to attach my piCamera to the front of the frame. First, I removed the pulley mount plate by unscrewing it. Then, I attached this piece...

UPDATE: A Rev2 Corner Foot has been added, featuring a beefed-up design with a wider side tab and a bottom frame rail that now rests snugly within the tab. The printer was in desperate need of some feet to bridge the gap between the metal frame and...

This adapter glides effortlessly through the stock spool holder, giving you the freedom to mount this versatile filament spool on the other side of your bracket for easy access and a clutter-free workspace.

The human requires two duplicate spool holders, each equipped with a sturdy three-quarter-inch PVC pipe.

Next, attach clips securely to your top-mounted filament holder!

I crafted this accessory to provide a clear view of my nozzle from the front of my printer, making it effortless to observe the initial layer and simply enhancing overall print visibility. ...So far, it has proven effective in meeting my needs.

The original design was reworked to accommodate a bigger size that perfectly fits into the 28mm space of the flashlight.

Requires four 3/4 inch bolts, four 6/8 bearings, and leftover parts from the remix like additional bolts, spacers, a nut, and wheels. This kit includes only the left and right arms with corresponding brackets. Both brackets are supposed to be...

A compact modification to enhance the functionality of the standard spool holder, allowing it to accommodate larger spools and provide up to an additional 10 millimeters of clearance space.

I really loved the LED mount by Rexipus, https://www.thingiverse.com/thing:1880015. However, it was a tad too large for my taste. To fix this issue, I redesigned the tray that holds the LED strip to accommodate only half of it, ensuring it still fits...

I've got a printer in my bedroom and the screen is way too bright to sleep with when I'm printing, so I created a cover to block out the light. I lined the inside of the screen cover with foam tape to really reduce the glow. ...Appreciate you reading...

A convenient clip-in adapter that allows easy passage of the filament without snagging as the material runs out.