maker knife 3d print

--------------------------------------- The new Spool Winder: You will need: Print the winder parts: WinderHandle - need 1 WInderHub - need 1 WinderLeft - need 2 WinderRight - need 2 SpoolHolderBaseA - need 2 SpoolHolderBaseB - need 2 Hardware...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

Installation ------------ Print out the four switch holders and slide them into the aluminium channel on the X and Y axis, as shown in the photos. The X axis holders are slightly longer than the Y axis holders. The tolerance is quite tight so they...

Buck Converter (to power my 12v cooling fans) Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so...

This gives me enough string that when I loosen the ligature I can easily get the reed on the mouthpiece, and when I tighten the mouthpiece I get as much tension as I could possibly want. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts:...

You may have to warm the rear Pipe Sockets a bit as you put the 8mm Pipe in, but depending on your printer, it'll just fit "Snugly", whereas 7mm Pipe will be a touch loose until you tighten down your bolts/nuts.Seriously, use PLA+ (PLUS) filament...

The single could be used in pairs at the junction point of the arches if desired or if your printer won't print the larger double base. I have supplied 4 different versions of the single with cable exits coming from different angles to allow for...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

Only a few parts are needed and it is easy to print, preferably in PETG.You can mount it in different ways, on a tripod, with a table clamp or simply with screws.I would still have to work a little on the software, but it works so far.The stepper...

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

all parts: layer height 0,2mm infill 10% to avoid an elephant's foot and thus to achieve an optimal fitting width, you can also print the plates with raft. a maximum of 100 pieces are needed. you can clip them by hand into the holders of the frame...

So I like to print a test piece before committing to anything big or sensitive. I find that making a piece of OS-Railway track using whatever filament is intended for the project is usually enough to warm up the bed and predict if the printer can be...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

The new mount plate prints easier. The new mount plate has better wiring management. The new mount plate allows for a small 8x8 heat sink to be adhered to the back of the Huvud board to cool the stepper driver on the reverse side. The new Huvud...

The flexible hose should be suspended overhead, centered on the work area and should have at least a 4 foot rise with ample slack so as not to place side loads on the tool anywhere within the work area. File Dust-Shoe-Mount.stl may be printed or cut...

The templates cut the rods a little short (3mm) so that there is room for any tolerance stackup in the X and Y axes.Some NotesAll of the parts (except for 1) are printable without supports I recommend 100% infill for the “Sand Cover” piece to...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

You'll want to print two each of the bottom stops with and without dowel, and as many of the top stops as you care to use to mark your positions. To finish/calibrate the stops, do the following: 1. Glue/epoxy 1/4" dowels into the holes. These...

6 is a hinged version, you need to print 3 of the hinges and 2 of the shafts.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:4654378 - Rivet Cutting...

These are an assortment of Dust Collection Accessories that I've printed. I may be adding more as I need them or possibly upon request for something. I've also added the actual dimensions to all the parts to make it easier for you to make sure these...

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

TRABAJO EN PROCESOCon este upgrade convertimos cualquier SIGMA a filamento de 1.75, usa extrusores Titan y Hotend V6 de E3D Original.Hemos respetado todos los componentes originales de la impresora, los ventiladores, el termistor y el cartucho...

This is better than putting an oscilloscope probe in your helping hands. Print instructionsRoadrunner Probe Revision A Released 2020-10-04 Copyright (c) 2020 Josh Myer josh@joshisanerd.com Released under a Creative Commons CC-BY-SA license What is...

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

Create solid lines from the bottom of the arcs at the top corners to the top of the diagonal lines at the bottom corners. Design Choices:To construct this paperclip, we created dimensions on graph paper, twice the size of how it will actually...