magsafe tripod 3d models

You can use them to mount the base on a tripod (if you dare), or connect multiple bases side by side fanning out the arms in in 15°, 30° or 45° angle (just in case you want to complete an octopus eventually). The electric drive is based on an...

It screws into the holes where the LCD is normally placed, which provides the strongest direct frame connection, and also the best front facing position for timelapse capture using Octolapse. Here is a timelapse example made with this and Octolapse:...

Thinner tends to be better, and I do not recommend going thicker than 3mm. To use, simply set up your camera on your tripod with your chosen lens, and attach the appropriately sized lens adaptor to the front. Slide the teleprompter onto the lens...

Note that the system won‘t stabilize movements in the Z direction (up and down movements). There is only few additional hardware needed:2x M4x30 screw2x M4x18 screw2x M4 nut1x rubber band¼ in to ¼ in male adapter like this (only needed for...

I also added a handle in front to make it convenient to move the hot table, but a threaded sleeve was also added to the handle for attaching a tripod head. I made a pen from wood, but the model is also in the archive. And the last thing I installed...

... put the camera with the case. It's up to you how to use the dock, you can put it on a cup for elevated view, or push and glue a 1/4-20 nut to the bottom and have a dock that screws to a tripod etc... ...I personally use it in my car cup holder.

Consequently, users resort to car mounts and tripods, and while these may work well for some, a strong argument for improvement can be made.Addressing the gap, the Rail-Mounted phone holder attempts to improve usability and aesthetics and changes the...

The body doesn't need more than 25% infill, but it doesn't hurt to make the screw up to 100% infill because it is literally the 1/4-20 that attaches the unit to the camera's tripod socket -- the rectangular head of the screw makes it easy to tighten...

:P In the future if I get around to it, axis clamps should be added so that a camera can be locked into position. Hardware needed is: 2 thrust bearings 9 ID x 20 OD x 7 high. 2 x 608 bearings 1 3/8" nut and 3/4" long bolt (to give the skimmer pod a...

With 3 independently driven lead screws that automatically level the bed before each print, and bed mapping to compensate for a bent piece of sheet metal used for the bed plate.Bed TiltA kinematic coupling bed mount is stable, like a tripod. When you...

Note, that you will also need a cheap Kellner or slightly better Plössl eyepiece (~10 €) or an eyepiece set and a (photographic) tripod with quarter-inch-screw mount. There are also m6 threads in the side of the telescope so you can attach a...

For the same amount of money it is possible to get a used but functional CG5 mount with a tripod. This seem to be better investment than 3D-printed DIY, just because stiffness issues of the plastic parts and timing belts. What renders long-duration...

Consequently, users resort to car mounts and tripods, and while these may work well for some, a strong argument for improvement can be made.Addressing the gap, the Rail-Mounted phone holder attempts to improve usability and aesthetics and changes the...

I also have a version of this tube which extends from 50-150mm, for shooting at 1-3x magnification with 50mm lenses: https://www.thingiverse.com/thing:4941924 (it can no longer focus to infinity, though) ## More macro accessories Pictured in the...

This provides a much more accurate temperature reading during daylight hours. The shield consists of several parts: Several rings that are open in the middle for sensor equipment Solid plates to shield the top and bottom A larger top plate to...

Somehow found this on Youtube, started printing but had so many problems that I ended up making almost everything from scratch (although my objective was to make a 3DOF **controller** for KSP and not necessarily a mouse) # Credit where it is due The...

 The second part is the “remote fixture”, which is just used to secure the camera remote to the printer, without interfering with the majority of prints (perhaps it could be an issue if you're using the entire print volume, but that's a pretty rare...

Cablecam diseñado por estudiantes del Tecnológico de Costa Rica para el curso de Sistemas de Manufactura- MT 8003Integrantes:Mario Araya AlvaradoCristian Murillo MoraDaniel Villalobos ZúñigaLink de piezas:Anillos de retencion:...

There is a hole and clearance underneath to take a screw to go into the tripod mount of a webcam. No support needed. The reverse bowden filament guide allows a 4mm OD PTFE tube to plug in near the spool holder to neatly guide the filament into the...

2 x 608 bearings 1 3/8" nut and 3/4" long bolt (to give the skimmer pod a common tripod bolt thread, and to allow the gimbal to screw onto it. 1 x 30 mm M8 bolt and nut for the vertical axis of the gimbal. 1 x 25mm M8 bolt with countersunk head and...

https://www.thingiverse.com/thing:4945992 I also have a 62-150mm version of this tube designed for Canon lenses on Canon cameras instead of Sony: https://www.thingiverse.com/thing:4975686 ## More macro accessories Pictured in the photos above are my...

Note, that you will also need a cheap Kellner or slightly better Plössl eyepiece (~10 €) or an eyepiece set and a (photographic) tripod with quarter-inch-screw mount. There are also m6 threads in the side of the telescope so you can attach a...

The description below refers to colors present in the renders. Detailed descriptionThe white tube provides the necessary height from the film plane and has the shape to accommodate the lens, while the green part (the camera base plate) provides...

if there is no STL with support or a sacrificial layer there should be no support needed.I also made an extra part for use with the Tripod Mobile Phone Clamp V2 and for the IKEA LAGRA lamps. Other parts can be added later as the connectors are all...

Budgie is an adapter for Leica M to Sony FE -- except it does offset shifting and includes a tripod mount. The name comes from the idea that the camera can be budged +/-12mm relative to the mounted lens to capture multiple images for stitching. The...

Personally I didn't find the need for this design, as the tripod is stable enough for my needs, but the option is there for those that want to opt for it.For those wondering, I consider the following configuration as "default" offering of the design....

if you Need freight crates/tanks for the model look here: https://www.thingiverse.com/thing:4288039 Watch for the tripod laser cannon from S1E1 here: https://www.thingiverse.com/thing:4305631 Printing Instructions: [update 07.04.20] I added a Body...

The terraPin OSKAR Tuxedo pinhole camera is an easy-to-print and assemble device, requiring only one lock nut and bolt for the shutter and a flanged 1/4-20 nut for the tripod mount. The 29 mm focal length provides a wide angle (approximately 110...

To test and adjust focus without using film:Mount the camera on a tripod and point it at a bright high contrast scene such as test on your computer monitor and measure the distance from the subject to the film plane (~46.5mm behind the front of the...

Or otherwise you may face fluffing strings during snap shot travels. CAMERA/PHONE SETTINGS: Locate the phone/camera somewhere close enough to see the model to be printed, properly (use a tripod to fix the camera strait and firm). Lighting is very...