magsafe phone stand 3d models

Iphone Magsafe phone holder. ...Holder width is 75mm.

A MagSafe charging puck stand.Remixed from the Articulating Pi Camera Mount, this is an adjustable stand for holding your phone or headphones.Required Parts to PrintHolder - Pick one of: no-tab, mini, regular, or max. The difference is the size of...

Charging stand compatible with Apple MagSafe : The charging station is compatible with all MagSafe cases. All you have to do is bring your iPhone, with or without a shell, to the magnetic surface and voila! Thanks to this support you can have your...

This is a simple small stand for a MOUS branded MagSafe charger that I made to be short enough to fit under my monitor. Fits snugly enough to hold in the charger with no need for glue or hardware. The extra-base plate is optional, but I added it...

This extremely convenient solution allows you to enjoy the fast charging of MagSafe for your iPhone 12 (or one of the other models in the range) whether in portrait or landscape mode. Easy magnetic alignment : With MagSafe technology, you get...

This dock gives a new purpose to the Magsafe Battery Pack, mounting it as a wireless charging stand for your iPhone 12. When you are at the desk it stands for a regular charging stand, but when you are ready to go just take the battery pack with you...

... to the new landscape widget mode in iOS 17. ...It snugly fits the MagSafe charger within the slotted hole in the stand and leaves enough room to not bend the charger cable too far. ...It works for me as a sort of bedside table clock while it charges.

I wanted a stand to turn my MagSafe charger into a charging dock that was elegant and minimal and wasted as little of the cord length as possible for cable routing. After a few designs, I landed on this one and I'm really happy with the result. Just...

Be aware though that there is no support shelf under the phone, so it relies on the MagSafe to hold it in place.With the phone case I use it didn't quite hold it strongly enough, so I added a circular magnet to the case made specifically for that...

iPhone 13 & 12 MagSafe Stand is strong enough to support all variants whilst remaining aesthetically pleasing with a small footprint and slim profile. Only 8mm thick it will support and charge your iPhone in both portrait or landscape. Free...

Welcome to my take on a MagSafe Charger Stand with an industrial yet sleek look, roughly based on similar stands in the apple store. This charger stand is designed to securely hold your iPhone in place using MagSafe technology, allowing it to appear...

UPDATE: 03/26/2021Added a “No Shelves” STL for those of you who want to solely rely on the magnets. This is a remix (the original is here https://www.thingiverse.com/thing:4655842), Thingiverse isn't finding remix links anymore.I am using the Pitaka...

I have made an adjustable MagSafe stand for the new range of iPhones! I previously made a stand that didn't move (https://www.thingiverse.com/thing:4661361) but wanted something that I was able to adjust the angle on. This model is made up of 5...

Easy to print design.UsagePress fit your magsafe charger (56mm diameter) into the slot at the top.Feed the end of the wire through the entry port at the back of the stand.Roll up any excess wire as needed inside the stand.Press the remaining wire...

Very rough design, but seems sturdy enough, designed for my old monoprice printer. ... I use a piece of double sided tape to hold the magsafe charger in it.

... ... The MagSafe is held in place by magnets and can be easily removed using the button on the back. ... Required parts: 14x magnets 3x1mm 2x magnets 7x7mm 1x M3 x 12-14 screw The magnets and the lower cover hold without glue.

I have created a 60 degree Support for my iPhone 12 Pro Max to fit my MagSafe wireless charger. Also you will find the MagSafe and the iPhone 12 Pro Max STLs. Although I added small feet support for that model, most likely the other models will...

... is not visible. ... The MagSafe is held in place by magnets and can be easily removed using the button on the back. ... Required parts: 14x magnets 3x1mm 2x magnets 7x7mm 1x M3 x 12-14 screw The magnets and the lower cover hold without glue.

Story i bought a magsafe charger that you install in the car vents but it didnt fit, so i made an adapter you use doublesided tape or glue to install. ...

I am using the Pitaka case that is supposedly MagSafe compatible but it definitely weakens the magnetic link between the MagSafe charger and the iPhone 12 Pro. I ended up adding a ledge to the bottom of the original design so that the iPhone lines...

I am using the Pitaka case that is supposedly MagSafe compatible but it definitely weakens the magnetic link between the MagSafe charger and the iPhone 12 Pro. I ended up adding a ledge to the bottom of the original design so that the iPhone lines...

Iphoe 12 MagSafe holder with magnetic cover so that the cable is not visible. The MagSafe is held in place by magnets and can be easily removed using the button on the back. Required parts: 14x magnets 3x1mm 2x magnets 7x7mm...

Designed to work ideally with an iPhone 14 Pro or similar sized iPhone (13, 13 Pro, 14 should be similar) to charge with Apple MagSafe USB-C charger. Printed with Duramic PLA, variable layer height, 0.6mm nozzle. Also works great with...

Holds Qi charging puck and supports iPhone models with MagSafe (probably not Max models). Power cord can be stored inside the case for transport. [edit] By request, a version 10mm longer has been added to support Max models. ...If you print one, I'd...

Remixed from: https://www.thingiverse.com/thing:4635725 Changes from original Thing: - Remixed to fit Wtuhu MagSafe charger from Amazon, found here: https://www.amazon.com/gp/product/B0C2BQ8NQC/ - Simplified interior geometry to reduce print time -...

Nice phone holder for the Audi A3. ...Fits inbetween the vents. You only need to buy a magsafe adhesive ring.

Modified magsafe cutting depth (reduced by 0.4mm) 2. Modify the wire cutting length (increase 7mm) 3. Apple logo. ## solved problem: 1. The camera bulges when the iphone mini is placed in landscape orientation. 2. More cable adaptations. >...

Holds your phone in place and loads it at the same time!

Remix from the pranabs Stand for iphone only owners

I can print it for you: https://www.etsy.com/listing/1308443280/1991-2005-nsx-wedge-magsafe-phone-mount \\ \\ \\ This phone mount specifically fits the 1991-2005 NSX. It fits between the center console and trim and supports the phone via a *MagSafe...