magsafe adapter 3d models

Remix of a remix to be used for adapting the clingo ball mount to a flat surface that you can stick on a MagSafe adapter.

... charger fits in just right and holds by grip fit. Note: I sell this magsafe adapter on my website, below. made from anodized aluminum with 1/4-20 female threaded hole, and includes this TPU piece. ... https://www.buckyourbronco.com/shop/p/magsafe

Keep track of your tiny, essential, MagSafe 2-to-MagSafe adapter with this magnetic keychain widget. This part is designed for iron-containing magnetic PLA from ProtoParadigm or Protopasta. Magnets in the adapter keep the two pieces firmly attached.

I have included a 3mf file, where all of this is already setup. Adding a 45 degree side from the overhang to the quadlock surface could probably do away with the support need, but unfortunately I could not get this done easily as the quadlock...

## Standard power cable MagSafe adapter This is adapter I designed to use any cable with the MagSafe. I had a 30 cm cable, so I thought it could be way more portable than the ~1.5m that the product comes with. Let me know if you run in any issues...

Replacement part for Macbook (Magsafe) power adapter. Once the cable breaks too close to the rubber grommet, you can open the adapter, cut or desolder the output wires inside, use this part as a new grommet and solder back the good part of the output...

Considering MagSafe could be a most popular charger used for iPhone product. ...We designed an adapter to can accommodate MagSafe dimension and fit into previous iphone and Apple Watch stand.

This is a very simple adapter which allows to replace the original very cumbersome phone holder from the Ikea LÅNESPELARE with a MagSafe Puck.The puck fits very tight and is hard to remove after putting the puck into the adapter.I added the FreeCad...

If you've a Nokia Qi Fatboy Charging Pillow laying around, you can now use it with 15 Watt Charging on your iPhone with help of a MagSafe Charger.

Adaptor to be able to charge your iPods with MagSafe. You can permanently leave the iPods in the adaptor. The USB hole, the button and the light are still accessible. You need to buy a magnet ring. I bought this one from Amazon :...

Things you need - screw M3x12 - https://amzn.eu/d/4kAWSfl

<p>Hi!</p><p>My best friend wanted to upgrade their IKEA wireless charger that was added to their nightstand. ...So I modeled this up and went through a few revisions.&nbsp;</p>

This is a holder to keep your MagSafe adapter from getting lost. I use a Unibody and Air so I was always taking the adapter off and didn't want to loose it. ... Designed to be a very tight fit off my printer.I didn't want it falling out.Your fit may...

This is a MagSafe adapter for a 77mm hole in a table. ...It prints in 3 and half hours.

This is a simple MagSafe adapter to mount onto my Myllra Adapter System.

Magsafe Power Adapter Cable Protect : D This is a remix. ...The Original is: http://www.thingiverse.com/thing:141012

/!\ UPDATE: A new updated version 2.0 with a cleaner a better model is available /!\ This design is a MagSafe adapter for a 77mm hole in a table. ... It prints in 3 and half hours.

Remixed Magnet holder part adapted to suit MagSafe sized Mounts. ... Specifically designed to fit the MagSafe mount I already had, Linked below https://www.amazon.co.uk/dp/B08T8RFVC7?ref=ppx_pop_mob_ap_share

A simple adapter plate to mount an official Apple Magsafe wireless charger to an iOttie 5 universal car mount phone holder. It uses original screws and is a simple swap over. Magsafe puck will be snug but might need some adhesive to keep secure in...

If your MagSafe adapter is still functioning, you may be interested in an accessory that can extend its life before searching for "how to fix MagSafe adapter." I have designed a small clip that reinforces the flexible end of the joining part between...

This is an adapter to use the Apple MagSafe charger for iPhone in the same place as the IKEA NORDMÄRKE for both the drill mount or the furniture built-in. The drill mount uses the IKEA FIXA drill set.</p> <p>I made the fit snug with no wiggle room. I...

Adapter for Skoda Citigo or Volkswagen Up which enables you to use the apple MagSafe charger and iPhone in horizontal or vertical position. Can be printed without supports in only 2 hours and it's easy to mount or demount. I recommend you the usage...

This is an adapter to use the Apple MagSafe charger for iPhone in the same place as the IKEA NORDMÄRKE for both the drill mount or the furniture built-in. The drill mount uses the IKEA FIXA drill set. I made the fit snug with no wiggle room. I did...

Since my car came with the Powerflex mount for mobile phones, I decided to disassemble this to see if I could convert it to Magsafe. This thing is what I came up with. I uses the backside of the original mount of the car and can is designed to...

If your MagSafe is still working and wish to prolong the life span before googling "How to fix MagSafe adapter". I have made this little clip that is able to strengthen the flexible end of the joining part between the cable and the adapter. I am...

THIS IS CURRENTLY UNTESTED, But I wanted to try to fuse together the phone holder and magsafe adapter so I booted up tinkercad and, yknow, fused the models together in some sort of abomination

Use Letscom Magsafe iPhone Charger with your brodit holder in your car.

This modification adds a more substantial lip around the MagSafe part to hold it tighter and angles it up to make it easier to face toward the driver.

... 42mm center-to-center. And fit M3-50 screws: https://www.homedepot.com/p/Everbilt-M3-0-5-x-8-mm-Zinc-Plated-Plain-Metric-Socket-Cap-Screw-3-Piece-per-Bag-803178/204808022 The Magsafe charger can hold my iPhone 12 Pro Max without additional support.

This is my first project. ... The Brodit adapter is for hole distance 37,3mm. Das ist mein erstes Projekt. Der Adapter geht für die Platten mit den Lochabstand von ca 37,3mm