magpul ctr cheek riser 3d models

I designed this 0.5-inch cheek riser specifically for Magpul MOE or CTR model buttstocks before discovering that pre-made versions are available on the market. The initial goal was to ensure proper alignment of my optics with my eye, prompting me to...

I had been craving a cheek riser for a CTR for some time, so finding the original design on Thingiverse was incredibly exciting. However, my current printer has a limited 120x120x120 print area, so I opted to scale down the design to 119mm in height....

cheek riser currently set up for working with the hydra mount. ...allows charging handle while fully collapsed.recommended to print with a brim on the flat side as theres not much surface area for adhesion.have printed in pla+, abs, and am currently...

cheek riser currently set up for working with the hydra mount. ...allows charging handle while fully collapsed.recommended to print with a brim on the flat side as there's not much surface area for adhesion.have printed in pla+, abs, and am currently...

Low cheek riser CTR/MOE. Designed specifically for airsoft guns, it provides a seamless fit without any issues. ...However, when the stock is fully extended on an AR-15 type charging handle, it may interfere with its operation.

Everything is in the title: it's a cheek riser for Magpul Zhukov AK stocks. I designed it because the risers from Magpul are (1) not high enough -- I needed +24mm to get a repeatable position behind the scope, and (2) in our parts (Europe) are...

This cheek riser clips onto the Magpul Zhukov folding stock, perfectly suited for AK pattern rifles. Its primary function is to position your eye in line with a micro red dot optic mounted on an RS Regulate mount. It performs well under light use...

This is a cheek riser that clips onto the Magpul Zhukov folding stock for AK pattern rifles. It is designed to put your eye in line with a micro red dot optic mounted on an RS Regulate mount. It holds up just fine with light use but I would recommend...

Cheek Rise for CTR and other MAGPUL stocks.

To make removing and remounting your Magpul CTR stock on your M4 airsoft rifle easier, create this tiny Magpul CTR stock removal tool. This 4-minute printable item is simple to replace if lost or broken. To mount the stock, press down on the locking...

Cheek Riser for Boyds at One Thumbhole Gunstock. ...I made that because precision shooting with high scope mountings. It makes adjustable cheek riser 2 cm higher than original. ...You need to use doublesided tape to mount that.

I wanted more custom cheek risers than the two sizes made by Magpul so I modeled the base of the default riser that comes with the Hunter X-22 stock and then made a custom top at different heights to fit my cheek perfectly at the height for my scope...

A basic helper to remove AR15 stocks, especially the CTR Magpul one.

I recently printed and improved the Magpul CTR stock design by HybridDK, which can be found at http://www.thingiverse.com/thing:316372. I added a ring and a small plate to enhance the original piece. The printing was done with a PowerSwap Evo, and I...

Original or copy CTR & MOE lacrosse cheek rest. If you like, you can find my other creations here : https://cults3d.com/fr/utilisateurs/AT_Eleven_3D/cr%C3%A9ations My facebook page: https://www.facebook.com/ATEleven3D Unless otherwise stated,...

Magpul CTR FDE Buttstock

Magpul CTR-Compact model.

Cheek riser replacement for FX Impact M3

13mm cheek riser for cz455 with boyds thumbhole stock.

This is an ambidextrous cheek pad that fits the Saber Tactical cheek riser only. I also have a stock frame version as well. ...these will not interchange.

This is a replacement ambidextrous cheek pad for the Impact. ...this is for the frame only replacement. I have one for the Saber tactical cheek riser as well

This is a stock cheek riser for the Thompson/Center T/CR22 stock made by Magpul, similar to their Hunter X-22 stock. This has a 4 degree slope canceling out the downward slope in most 10/22 stocks. This puts the surface parallel to the bore so that...

It is designed to fit the original MagPul CTR stock and can also be mounted on replica (Kublai) stock. ... Requirement M5 x 12 flat head screw x 1EA (fit Replica) 10-24 x 5/8" flat head screw x 1EA (fit Original) 1.5~2mm metal or carbon rod...

I designed this stock cheek riser for my savage MKII, but it will work with any stock that has a comb roughly 1" wide. I used a cheap mouse pad and rolled it up to provide space between my rifle's stock and the cheek riser. Any foam or fabric will do...

... optics as opposed to an unaltered model where the pad aligns with standard iron sights. ...Tested on a JG G36KV airsoft stock; this modification benefits users. Find more details at http://argoms.blogspot.co.uk/2014/09/g36kv-stock-cheek-riser.html.

A cheek riser for the Sako Quad rimfire rifle. There are 2 files: One that'll give you a height of 25 mm and one that'll give you 23 mm. There are openings for adding velcro straps, but I use some kind of construction adheasive and no straps. ... ...

Spacer for SL8 cheek rest

cheek rest for hera_CQR stocks

cheek rest for hera_CQR stocks

This cheek riser will fit the CAR/N1 Fiberlite style stock to get a better cheek weld for carry handle mounted optics. Note that this fits tightly and will probably scratch the plastic of the stock slightly. I would not use it on the coated aluminum...