magnets harbor freight 3d models
70367 3d models found related to magnets harbor freight.thingiverse
I love the 18in Harbor Freight Magnetic Tool Holders. I have several in my garage and office. I recently dropped a big thing of small screws and nuts and most magnetic sweepers are way too expensive for me for occasional use. Harbor Freight has a...
thingiverse
The other connector used small magnets that didn't work well so, with the rush of the new movie coming out and needing to have this done, I made it work with what I could find: hook magnets at harbor freight and a big honking UDJ fender washer from...
prusaprinters
The other connector used small magnets that didn't work well so, with the rush of the new movie coming out and needing to have this done, I made it work with what I could find: hook magnets at harbor freight and a big honking UDJ fender washer from...
thingiverse
This is to adapt a Harbor Freight magnetic base to a 1/4-20 thread for mounting mics, cameras, and other things to it. ... Watch This Video to see what it's for https://youtu.be/oca56SyahMQ
thingiverse
Just a quick cap I made to cover the ends of the Harbor Freight Magnetic Hooks. Print with a Brim just to help it adhere to the bed, since it's so small. I did 4 at once with the brim. ...Print with the hole facing up.
pinshape
You'll need a Harbor Freight magnetic base (or grab one on Amazon, assuming the rod sizes are the same), 1/4-20 threaded rods and nuts for it....oh yeah, and a GoPro. ... Assembly and ideas for usage can be found in my YouTube video for this project at...
thingiverse
I picked up a magnetic tool bar from Harbor Freight [(item # 60433)](https://www.harborfreight.com/18-in-magnetic-tool-holder-60433.html) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall...
cults3d
I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...
prusaprinters
I picked up a magnetic tool bar from Harbor Freight (item # 60433) and was disappointed that the mounting holes were not 16" on center so I could mount it securely to my wall studs. Sure, I could use wall anchors, but what fun is that when you have a...
thingiverse
This is a magnetic bit holder for a Harbor Freight Bauer 20V drill or driver. It uses two 8x2mm round magnets that you must glue in. ...The holder has two 15mm deep hex slots for shorter bits and can hold a long bit or drill bit on the outside.
thingiverse
The Harbor Freight Magnets are around $2 per pack: https://www.harborfreight.com/home/toys-hobbies/magnets/ceramic-magnet-assortment-16-pc-58066.html These are designed for the round ceramic magnets with Diameters of 18mm and 25mm. They are 6.5mm...
prusaprinters
I just took their idea and remodeled it for use with Harbor Freight's ceramic magnet pack.Different versions made for 1/8"(3mm) and 1/16"(1.5mm) material.The Harbor Freight Magnets are around $2 per pack:...
thingiverse
I struggled to locate the 20 mm x 15mm x 6 mm magnets that Prusa recommended so I discovered these rare earth magnets at Harbor Freight for three dollars which worked perfectly and I remixed their knob. Magnets can be found here:...
prusaprinters
This is a model for skadis hooks that hold harbor freights version of magnetic tool holder. The link is: https://www.harborfreight.com/18-in-magnetic-tool-holder-60433.html
thingiverse
Ripped the magnet off a Harbor Freight magnetic dish and glued it into this spot.
thingiverse
Printed in PETG+, I remixed the original design from user Samhyamss to accommodate the slightly larger dimensions of the Magnetic Tool Holder from Harbor Freight. ...Fit is snug and filament should just barely stretch to fit the clips into the Skadis...
thingiverse
hotbrass made a fantastic dual-flashlight housing that uses the guts from two of the free Harbor Freight flashlights. It loses the annoying button that toggles between the big bright light and the weak/useless one and adds a second bright light. I...
prusaprinters
I was looking for a way to add a magnetic tool holder to my K1-Max, Harbor Freight Item Numbers : 60433, 65489, 61199, 62178, these are what I came up with. Your choice : one for 3mm, 4mm, or 5mm heat set inserts (the 5mm may work best). I used the...
prusaprinters
... magnet into the 6mm hole. ...Use 5minute epoxy to glue to your ratchet. Magnets I used:https://www.amazon.com/gp/product/B07KLV4D3D/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1Attached is the SolidWorks file if anyone wants to make edits.
thingiverse
Replacement slide on 3/8 drive socket holder insert for the Harbor Freight magnet organizer. ...Friction fit rather than ball bearing snap but it works fine.
thingiverse
A custom enclosure is built to hold a Harbor Freight multimeter securely in place. ...Additional storage compartments are integrated into the design, allowing for magnets to be stored within easy reach.
cults3d
I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.
thingiverse
I made these for the Harbor freight featherboard. ...The original inserts do not fit the Harbor Freight 10" table saw so I made new ones.
thingiverse
A box and lid to securely hold set of Harbor Freight Probes. ... There is a remix that is a box for mini files from Harbor Freight as well.
thingiverse
I think this is the medium size vice from Harbor Freight best printed out of TPU.
thingiverse
I created a Harbor Freight flashlight holder that lets me illuminate the dark spaces around my machine at work when I'm swapping tools. This design relies on five millimeter by five millimeter by three millimeter thick magnets for its stability.
myminifactory
I created this Harbor Freight flashlight holder to illuminate tight spaces when changing tools on my machine at work. The holder utilizes 5mm x 5mm x 3mm thick magnets for secure attachment. ...I've also made available the Fusion 360 file, allowing...
cults3d
Quick socket organizers I made for harbor freight deep well socket sets. ...I've included a file for both SAE and metric sets.