magnetic rc body mounts 3d models

This is a universal front and rear magnetic RC body mount designed specifically for the Sakura D4 chassis, but its versatility allows for easy adaptation to various other RC car chassis models.

Magnetic Body Mount 6mm - A Versatile Fastening Solution

I wasn't too fond of the idea of gluing magnets to my RC so I decided to develop a cleaner, simpler way to mount them. Tips: 1.) Print at 100% infill 2.) You'll need: (1) 15mm x 2.5mm round rare earth magnets with a 5mm hole (1) cup (1) spacer (1)...

Made this to use the existing mounting holes and mounting brackets on one of my crawlers..The posts are 6mm with 2.5mm holes @ approx 6mm on center. magnets used are 10m x 25mm x 3mm... ... printed in petg 100% infill 5-18-23 added round version for...

Magnetic Body Mount for RC Drift Car / Race Car

Some quick magnet holders to hold RC drift bodies on to chassis with magnets nothing flash but helps retain the body when you clip the track barriers side ways.2 versions V2 has slightly deaper edges to retain the body better.Can be seen here:

Some quick magnet holders to hold RC drift bodies on to chassis with magnets nothing flash but helps retain the body when you clip the track barriers side ways.2 versions V2 has slightly deaper edges to retain the body better.Can be seen here: 

Clippless magnetic body mounting system for 1/10 RC. No more holes and sticking poles from the body. You will need: -Magnets -14 M3 screws -washers (optional, for adjusting the mount width) Added a washer STL to save you a trip to the hardware...

The innovation was designed to free RC vehicle shells from traditional drilling and clipping methods by allowing them to be securely held in place with magnets.

The 90-degree adapter is specifically designed for use with the MST RMX 2.0's magnetic mount. Instead of attaching the magnet to the rear window, this adapter relocates it to the trunk, eliminating the risk of damage or sticking. ...With two adjustable...

... Información del mod https://cet3d.top/proto36-rc-car-posts/proto36-body-mounts/ Información general https://cet3d.top/proto36-rc-car-posts/proto36-rc-car-informacion/ Vídeo de presentación del proyecto https://www.youtube.com/watch?v=L1OxX1gPcJw

&nbsp;&nbsp;You will also need 12mmx3mm magnets, and some 1.5mmx15mm screws to attach it.&nbsp;It is designed for the screw to go through the factory body mount (to allow for adjustability). &nbsp;The magnets press-fit into the bottom. &nbsp;</p><p>I...

# RC Guided Magnetic Body Mount Just drop the RC Body over chassis, and voila! Mount RC Body has never been so easy! Just place a piece of double-sided tape in the RC Body to fix the magnectic and this thing. Please see the pictures for more...

RC body rear magnetic mount (for HPI 1/10 RS4 RTR).

One Piece RC Body Mount. Designed Specifically For 15mm Circular Magnets And Posts Ranging From 5.5 To 6 Millimeters In Diameter. ...Prints Smoothly With Ease.

Print the one-piece RC body mount now. It snugly fits a 15mm circular magnet and securely holds onto posts with diameters ranging from 5.5mm to 6mm. ...Printing it is surprisingly easy, even for beginners.

Magnetic Body Mount for 15mm Magnets. Print with a strong material to ensure durability. Not ideal for extreme use, but perfect for scale crawlers, trail trucks, on-road cars and drift cars. Secure the top piece to the lower one using an M3x12mm bolt...

Magnetic Body Mount for 15mm Circular Magnets: A Versatile Design. Printing is straightforward, but we strongly advise selecting a robust material to ensure these mounts withstand daily wear and tear. Not ideal for high-impact activities or...

Magnetic mounts for the body are designed for a magnet with a size of 10x1mm. The magnet is pressed into the mounting head before assembly. For a better entry of the magnet, the head can be heated for a short time with a hair dryer. Support...

These mounts will work to attach an Axial SCX24 Jeep Gladiator body to the Traxxas TRX4m. They fit between the stock shock mounts using 16mmx2.5mm hardware. Four 5/16" x1/8" rare earth magnets were used. ShoeGoo was used to attach the upper plates to...

This is a since screw body mount for 70mm width chassis and could be adapted to something like a Gspeed chassis as well. The sides are meant to press in an M3 heat insert inside. An M3 cap head screw is meant to act as a body post. ...You can use a nut...

Made a universal magnetic holder for RC bodies which adapts a little bit to the contour of the body. Post diameter is 6mm. You'll need: 4x M3x6 screws 4x M3 nuts 8x small & flat magnets (mine have diameter of 10mm) I included a shorty version for...

I was unsatisfied with the commercially available magnetic body mounts for the TRX-4 because the magnets were weak. So, I designed my own. They use 3/4" x 1/8" countersunk N52 round magnets with 10.5 pounds of pulling force per magnet. There are two...

I used mounts that accommodate 6mm x 3mm magnets, which can be found at: https://smile.amazon.com/gp/product/B077K364Z7/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 My custom body had to be significantly taller than the standard Jeep body, so...

This thing replaces the stock body posts and cross members on the Tamiya Bullhead with parts to mount the body with magnets. You're going to need a 2.5mm and 3mm drill bit as the front body parts need 2 additional holes each. Also there's 2 types...

Love my Venom Gambler, but always hated the body mounts were soft and too flexible. Decided to re-draw them, very basic, but I feel a better heavy-duty version. ... I also decided to re-do the posts as well, just so it is a complete set up.

Love my Venom Gambler, but always hated the body mounts were soft and too flexible. Decided to re-draw them, very basic, but I feel a better heavy-duty version. ... I also decided to re-do the posts as well, just so it is a complete set up.

I made these as a universal lift that attaches to both shock and shock mounting point. I used tpu but any material can be used youll just need to adjust size based on your car. ...These were made for an rc car I got from china that still has higher end...

mounts them selves allow quite a bit of adjustment in height. These things are rough I just made them quick and sloppy as a stop gap but dammit they are still working.Sized for 12x3 disc magnets, I like these ones:https://amzn.to/44vH8P8Also these...

Adjustable mounts for Traxxas Tmaxx enable precise positioning of the magnet on any body shape. Featuring a three-piece design, these mounts utilize M3 nuts and bolts to secure the 10mm magnets in place. ...To ensure print stability, use a large brim...