magnetic paddles mod for logitech g29 5 xc2 xb0 angle by 3d models

This is an adapter that allows you to fit a full size (70mm base) wheel to the Logitech wheel base. ... Extensively tested and works without any issues.

This is a mix of parts I found along with a couple I created to mount a Logitech C270 to the side rail of my Ender 5. It uses M3 bolts with T-nuts to lock it to the extrusion and then another M3 nut and bolt to hold the swivel point. The go prop...

You're looking at an innovative way to customize your gaming experience, aren't you? ...The paddles on these devices clip right onto the back of a PS4 controller, allowing for a DIY approach to replicating the acclaimed SCUF tech.

This is a mix of parts I found along with a couple I created to mount a Logitech C270 to the side rail of my Ender 5. It uses M3 bolts with T-nuts to lock it to the extrusion and then another M3 nut and bolt to hold the swivel point. The go prop...

... but decided to make some tweaks. ...My modification adds reinforcement to the threaded part, addressing a issue I encountered when trying to remove supports. The thread area would break apart easily, so this mod is my attempt to fix that problem.

Thread: M18 x 1,5 Adapter coming soon

... delivering a far superior feel and precision. ...All it takes is a set of cutting-edge 3D printed or CNC-machined components, a few high-performance springs, and a state-of-the-art magnetic Hall effect sensor to achieve this level of advancement.

... parts: the outer disc and the letters in the middle. I made it this way so i could easily spraypaint the letters in another color compared to the outer ring. I printed it in .12 resolution for optimal details in the letters, with an infill of 5%.

#F1 Wheel for Logitech G29 #Requirements - 4 x M4x18 screws and nuts - 1 x M4x14 screw and nut - 1 x M4 washer (optional) - 1 vinyl carbon sheet (optional) - epoxy (to glue handles with handle fixations, but optional) #Installation To install the...

Narrower version by Weissnix4711 The pin needs to be ground!

Model requested by a Cults user. It takes advantage of the screw of the original knob, screwing the adapter and on this same the knob, The use of PETG is recommended, although PLA can also be used. ... If you want a specific model can be designed, do...

print main part upside down for best resultsbetter than 0.2 layer height

I designed two uncomplicated printing spacer options for users. ...The initial version completely replaces the original spacer, while the secondary option is an adjustable piece that can be installed beneath the existing spacer to customize pedal...

I printed the source extensions as a hopeful fix which did make it better, however I found that the provided height extensions didn't want to work well with it, so I extended the extensions height and added a more grippy surface over the original...

I've remade them from scratch, using the previously printed parts as a reference for measurements to create both long and short versions that fit very snuggly and are stable. There is some extra extrusion once installed, but I found it to be...

I have updated a few things the collection of parts that jalexand posted to mount a Logitech C270 to a Creality Ender 5 printer. Mounting bracket to 20x20 channel. Designed a beefier version with more support and a key on the back. Use CA glue...

The paddles snap securely onto the rear of a PS4 controller, empowering users to recreate the innovative Scuf design at home.

This paddle attachment clips seamlessly onto the rear of a standard PS4 controller, empowering users to recreate the renowned Scuf design with ease.

... as a method of mounting a webcam. ...The camera mount integrates to a push fit bolt cover. For matching plain cover please see my other models.Hardware:------------------3 x M3 OD4.2mm L4-5mm heat inserts.3 x M3 (10mm) fasteners of suitable length.

... as a method of mounting a webcam. ...The camera mount integrates to a push fit bolt cover. For matching plain cover please see my other models.Hardware:------------------3 x M3 OD4.2mm L4-5mm heat inserts.3 x M3 (10mm) fasteners of suitable length.

Although brilliant in normal use, it fails to get the lens close to the frame or at a good angle without bumping into the print head.So I made my own case for the camera that will allow me to put it where I deemed the best place for it. ...(for now)I...

The holes for the magnets are quite tight, so it's essential to use a 6mm drill to ream them out before inserting the magnets using a pair of pliers. To complete this project, you'll need the following parts: * Four neodymium magnets (each...

This is a magnetic paddle shifter mod for Thrustmaster T150/TMX. I made two versions, one for 8x4mm and one for 10x3mm neodymium magnets. To stick them on, I used some double-sided 3M tape. I recommend sticking a piece of TESA tape on the magnets....

This is Magnetic Paddle Shifter MOD for Thrustmaster T300 RS. ... BoM: 1x 5mm or 8mm bracket 1x M3x10 1x M3 nut 4x 10x3 (or 8x 10x2) mm Neodymium magnets 1x 2-component adhesive (Epoxy) Video: https://www.youtube.com/watch?v=PORMB1qgojM

This is Magnetic Paddle Shifter MOD for Thrustmaster T300 RS. ... **BoM:** 1x 5mm or 8mm bracket 1x M3x10 1x M3 nut 4x 10x3 (or 8x 10x2) mm Neodymium magnets 1x 2-component adhesive (Epoxy) Video: https://www.youtube.com/watch?v=PORMB1qgojM

Magnetic/tripod mount for a Logitech C310. Changes to Magnetic camera mount: Larger hole for the tripod screw Moved tripod screw hole to accomodate larger mount plate 6x 6mm magnets instead of .3x 8mm Changes to Tripod mount for Logitech C310...

Did an angle correction where the magnets are attached, so that there is no gap anymore. It's a nice, easy mod with huge effect. Thanks for stanoba for this mod! ...:-)

[This](https://www.thingiverse.com/thing:3343488) seemed to be a perfectly fine mod but after printing it I noticed that it is too short / too far from the metal paddle arms to get a good magnetic pull, at least with the magnets I have. I remodelled...

## Changes to _Magnetic camera mount_: * A larger hole is added for the tripod screw * The location of the tripod screw hole is adjusted to accommodate a larger mount plate * Six 6mm magnets are used instead of three .3x 8mm magnets ## Changes to...

If you're looking for more customization options, check out my easy magnetic paddle shifter mod here: https://www.thingiverse.com/thing:3411628. ... You can also buy the finished printed parts directly from my Etsy store:...