macsquant analyzer 10 3d models

Holder for Analog Discovery 2 Logic Analyzer / Scope The holder snuggly fits inside the Analog Digital 2 and possible other Digilent Logic Analyzers / Scopes. Really convenient! You can mount the holder both horizontally or vertically. I...

The ProMinent CL2/pH Analyzer is a DACA (Digital Analog Converter) device specifically designed for pH measurement. This advanced instrument, known as DACB, offers accurate and reliable readings that are crucial for maintaining optimal water quality...

Remixed Case for LCSOFT CY7C68013A logic analyzer clone" by jamesglanville I edited OpenSCAD to remove switch and screw holes, friction fit was tight enough. (set to 0 size to remove) edited screw to allow to use counter sunk screws. added comments...

Housing for an arduino nano handheld gas analyzer with two MQ4, LCD1602 sensors and a battery. On top of the screen you need to paste plexiglass 2mm. Firmware, electrical circuit and photos of the product later. I will be glad to comments,...

The Ducati Data Analyzer (DDA) storage device consists of two components: the dongle and the USB connector cap. It serves multiple purposes, such as keeping the cap and dongle together, protecting the dongle's interface connector, and allowing...

A bezel/button cover for the soft buttons on the right side of the display on a HP 8757C network analyzer. This bezel snaps in place as the original part did, and in a different thing I have one that fits the CRT based 8757A. Though very similar,...

Edited version of the GNSS performance analyzer. Edited size and angle of the mouting tab so that the mount can be placed behind the shock tower. This allows for a lower mount and for the screws to be placed directly in the print material. Also...

circuit scheme and code -------------------------------- https://create.arduino.cc/projecthub/shajeeb/32-band-audio-spectrum-visualizer-analyzer-902f51 front side ------------ - matrix display 32x8 LED MAX7219 - volume button top side ----------- -...

Analyzer (tester) of metal powder fluidity using calibrated funnels Appointment Measurement of powder fluidity. Application areas Analysis of metal powders in industrial and scientific laboratories. Features Tested samples — metal powders The...

This case is designed to safeguard the exceptional RigExpert AA-30.Zero HF Antenna Analyzer (0.06 to 30 MHz), which also features a Moyina FT232RL USB to TTL serial converter that functions perfectly with AntScope, AntScope2, and for updating the...

If you wish to create custom accessories for HP Network or Spectrum Analyzers, including bespoke probes, pre-amps, fixtures, etc., being able to power them from this internal source rather than relying on a separate power brick or batteries is highly...

DSLogic successfully received funding by a staggering 1115%; hence, it will be shipped accompanied by a case. The designer of the product also crafted a bumper, intending for easy access to the PCB's extra pins. For more details about DSLogic, check...

Renders shown where made with Cinema 4D's standard and physical renderer. ...The .c4d version and .fbx version should be near identical, maybe you need to tone down the reflection on the .fbx screen texture.

This is a remake of the low-profile version from https://www.thingiverse.com/thing:2153437 by @bobtidey. I made a cap for the power button, lengthened the lid 1mm to center it perfectly over the I/O pins and added a small hole above the reset switch...

Designed for printing in TPU, for a pressure fit.

This is a fresh take on the design.\r\nI'm not a fan of toggle switches. When they're left out or scattered around a workspace, the toggle switch often gets flipped to ON by accident, draining the battery.\r\nNext time you want to use it for just a...

... ...Instructions for use include setting Tool_Length to 10, Nut_Size to 10, a feed rate of $fs at 0.1, Tool_Height at 6, a message length of 10 mm, using the 'write/Letters.dxf' font, and including a holding cap (Has_holding_cap = 1).

Task Number 10: Just to make sure I have this right, you are asking me to spin the given text which is "Problem #10" into another sentence or phrase while maintaining its original essence and keeping it within a limit of 60 words. ...Am I correct in my...

For the customization, set LEAN_ANGLE to 20, NUM_PENCILS to 8, PENCIL_SHIFT at 30, PENCIL_DIAMETER as 10, PENCIL_LENGTH to 190, WALL_WIDTH to 1, and BASE_HEIGHT at 10. ### What to use AI for? The AI is used to rewrite the text in a concise way...

http://www.thingiverse.com/apps/customizer/run?thing_id=28405 Instructions Using the following options: pitch = 12 degrees t = 3.5 inches in length d = 12 inches in diameter l = 22 feet long type = a straight line links = 10 parts connected together...

http://www.thingiverse.com/apps/customizer/run?thing_id=41524 Instructions Using the following options: Ring Width is Set to 6 Inner Message is Left Blank Ring Size is Fixed at 19.76 Font Spacing is Tucked in at -29 Font Size is Standard at 10 Ring...

- approximate_number_of_teeth_on_sun: set to 25 teeth - diameter of gears, w: set to 6.7 mm - planetary gear ratio, P: set to 50 to 1 - tooth count for small planets, T: set to 10 teeth - sun gear size adjustment factor, D: set to 50% -...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: bar_color = DarkGray font_outline_width = 1.5 barextruder = extruder2 outline_color = Blue font_size = 30 lug_text_distance = 7 bar_length_trim =...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: pulley_b_ht is set to 0, retainer_ht is set to 1.5, idler_ht is also set to 1.5, pulley_b_dia is set to 0, idler is off, additional_tooth_depth...

Designed this to unite jumper cables to a 2x5 pin plug for the cheap 8ch logic analyzer which came just with loose cables.Add some UHU hard plastic glue to make permanent.

I'm starting work on a three part design, with a part to bolt directly on to the coin counter to feed the coin analyzer, a part that incases the coin analyzer and then separately, a part to funnel coins into containers. I plan on releasing these...

These parts are part of my eevBlog project here: https://www.eevblog.com/forum/testgear/diy-logic-probes-alternate-approach-using-tks-adapter-pcb/msg4326775/#msg4326775 Shells for eevBlogger TK's adapter to fit HP Logic Analyzer Pods to Siglent MSOs...

1/16/2024This part bolts directly to the coin counter and is designed to feed a coin analyzer. This design was made in hopes to achieve 500 coins per minute (cpm), This design is currently untested, but will be tested tomorrow. If I get ~300 cpm from...

Github project: https://github.com/nadamas2000/soundAlert-soundAnalyzer-ESP32 Hardware: * Microcontroller Board: Heltec Wifi Kit 32 V3 (ESP32) * Microphone: Max9814 * Battery Holder: 3xAA Battery Holder / 1x18650 Battery Holder References: * Heltec...