mack rs700l model

Anyways, this is getting out of hand so here's the important stuff: Many models to choose from! 18mm sensor 12mm sensor 8mm sensor Then choose you cap: 2 stock fans with chain mount 2 stock fans no chain mount No fans no chain mount No...

Different sizes and materials will result in orbs with different focal distances, which may mean you have to adjust the model for yours. Print it strong-- thick walls are a must. You'd be surprised how heavy the orb is. Also, I had to "floss" the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

... assemble the mouse similarly to how to disassemble the G305 and use the same screws. (Check). Make sure that everything fits nicely and that all supports are removed. Supports can be deceiving, so check the original model if you need to. ...

Included with this design is the original (unmodified) hull files, a number of custom designed parts, an example list of hardware & electronics that can be used, and links to other Thingiverse parts to aid in completing this as a fully functioning...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

You can subscribe to my youtube channel if you would like to receive a notification when it comes out.There are so much detail on the model to help hide the layer lines that I do not find it necessary to do any sanding. I did spray the frame first...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

After sanding the putty flat, paint it using model paint or cover it with a large sticker to conceal any imperfections. Test fit the Laforge diversity module into the hole where the old receiver used to be. Cut off this standoff because it's...

Lastly, 5) It's ideal that any new design incorporates adaptability tailored towards various unique setups ensuring optimal calibration results across differing conditions allowing me customize freely as I work alongside other solutions which prove...

... 4 mm have been printed. If you're printing at a 0.2 mm layer height, simply add a color change at 4.2 mm (layer 21).If you're looking to make the game conveniently portable, check out Thessiell's lid. Don't forget to rate and share your make!

 I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers. UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table.  I decided to make a second unit to move...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

 I'm confident anyone here can just casually rotate the model right-side up in your slicer.This is licensed CC BY-SA 4.0.  Please feel free to republish this.  Feel free to remix this.  Feel free to use it for commercial purposes and make loads of...

this model the reason I like it better is because it locks into place then you just press the button and it works so nicer better than the others hear that you just hold it in with pressure. Arduino program settings this is all new to me I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_rotation = 0 custom_top_port_corner_resolution = 8 custom_right_port_corner_resolution = 8...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

I do not own a BL Touch so this design was based on 3D models so definitely WIP. I have increased the thickness of the Duct mount to the base unit to make it even more robust on the LH duct. You may now need to use M3 x 10 mm to fix to the base unit....

I also made some design changes to this model. First, because of the ninjaflex's floppiness, I was worried that the semiflex would not be much better, so I included a small piece that could fit into the charging port of the phone, the goal being...

Instructions First make sure the nozzle diameter and layer height match your slicer's settings, as by default the model is exactly 2 nozzle-diameters thick in each slice so as to avoid generating any fill paths (which would show up when lit). Also,...

In this model (and most other barn door star trackers) the threaded rod constrains the main gear, and is itself constrained by the hole in the acrylic. As the hole in the perspex has to have some leeway for the threaded rod, this could result in...

I know, it's specifically for the Ender 3 & I am using a Mega Zero, so no surprise that it does not work but I have no idea why before now I didn't see the problem when using these Ender 3 designed mounts with my Mega Zero, even if I'd mirrored the...

...March 23rd - Created a smaller prototype mockup for the bottom, mid and top tray using measurements from the full sized model. Experiencing corner lift on the middle tray, even with brims and the lid/bottom of the middle tray is about 1mm too short.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 97 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Not a problem with a well-tuned MK3S+.&nbsp; &nbsp; The box was printed usingFilament &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;...

I think the finished model and results (fish caught) where well worth the effort. The bait is printed in two halves and then glued together. (I used super glue) Three small pieces of 1.75mm filament are use to aid in aligning the halves while...