mack a model

Then I spun the large gear around and tightened the small gear between the two extremes I found This way both front gears are about flush with each other Instructions I printed these gears in PLA with 0.5mm nozzle Adjust temperatures as needed for...

GearBest sent me a Creality Ender 3 to test, and I'm blown away by its impressive print quality for such an affordable price. This 3D printer truly delivers! Buy the Creality Ender 3: Affiliate (EU Plug) -...

The Reaper paints in the upright position have a little play in them but will still be held without falling over or getting trapped. I designed it more for the inverted position as that is the way I hold my paints to prevent tip dry out. With the...

If you want the base to fit a different Veyron casting please send me the dimensions indicated here: https://imgur.com/5T6mb2L The display base is separated into 3 parts for easy printing and colour swap. The parts are: 1) Base -BaseV3.STL 2)...

You can perform the Firmware update as easy as putting firmware.bin onto a Micro SD Card and power up the printer while inserted. Only issue is that the printer loses the calibration with each Firmware update, so you need to redo it after the update ...

12 Euro hierzulande im internet kaufen, wer mehr Zeit hat, bekommt es günstiger beim großen A in Asien. Die Höhe der Teile ist so gewählt, daß der ESP32 Cam den Zähler noch scharf stellen kann. Dazu muss die Kamera aber manuell justiert werden. Dazu...

Using screws with a thread length of at least 37mm assemble as seen in the "full wheel.step" file 4. Disassemble the E4T encoder and remove the lens of the encoder (to protect it during assembly) 5. Attach the body of the encoder to the "body" 3d...

This is a case for Alex Gyver famous lamp using cheap lampshade (other one) Everything is friction fit and assembles and disassembles easily. Feel free to tune tolerances in fusion 360 for your needs I've also made two PCBs for this project, one with...

Honda Racing F1 Team se retire brutalement de la compétition à la fin 2008 alors même qu'un budget important a été consacré au développement de la monoplace destinée à disputer la saison 2009. Ross Brawn, directeur technique de Honda et plusieurs de...

The nylocks will make sure nothing gets unscrewed. Print orientation is crutial as it affects the strength of the parts, so I have included a screenshot of the suggested (and tested) print orientation (The parts should be in the correct...

####X#####################Y#####################Z#####################A#### # ########################################################################### [extruder] step_pin: PD6 dir_pin: !PD3 enable_pin: !PB3 microsteps: 16 rotation_distance:...

Users can also access this information through Shapeways: http://shpws.me/N4we, a customized version of which was created using Thingiverse's Customizer! found at http://www.thingiverse.com/apps/customizer/run?thing_id=209005. This data is part of...

Human: FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title: Maker the Bot Thing URL: http://www.thingiverse.com/thing:11498 Thing Author: cymon Thing Licence: Creative Commons - Attribution - Share Alike Thing...

Only you need a small gap/space (5 mm) between back side of the hamster wheel after “wheel_nut” before self locking nut. Use the flat wrench when tightening the hamster wheel to the cage so that the nut does not tighten too close to the wheel...

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: [0] Object Title: Electronic Dice Packaging [0] Object URL: http://www.thingiverse.com/thing:17963 [0] Object Author: M_G [0] Object Licence: Creative Commons -...

*30.05.2021 I replaced the files with updated version:* - Thicker backplate (2mm -> 3mm) - Thicker heatsink hilder - Two holes in the wire hilder plate for convenient cable tie use This is a single piece adapter to upgrade your Creality CR-10 or...

There is normally a tab / section in your software.. the lines you need to add are, Add these AFTER the G28 (Home) command. M851 Z-1.7 ; Z Offset M500 ; Save to Eeprom G28 ; Home G29 ; Level bed etc... The Z offset can be set above. Z-1.0 = 1mm.. so...

When you have printed the two wall plate sections & rails, run a length of Nano tape over the rails (this tape ensures some springiness to the copper strip,ensuring there is always contact betwen the copper rails & the copper strips on the back of...

If you enjoyed this project please share your make, leave a Like and Collect for the community or post it on Facebook or Instagramm To show your acknowledgment and support for my large Effort on this you can donate via PayPal. janoerter@web.de ...

With a 0% complaint rate, 1st place in re-purchase rate, and 1st place in recommendation rate, our company is trusted by customers for its reasonable prices and honest sales approach. We will always think from the customer's perspective and sell...

A customized version of http://www.thingiverse.com/thing:49590, made with the Customizer app, has specific settings as follows: - Front port 5 circle radius set to 0 - Front port 2 height set to 0 - Left port 2 rectangle width set to 0 - Front port 2...

Currently I found no possibilty to adjust these intolerance, so I have realize a tool to do so. With this tool you can adjust the angle between the 2 pipes of the Primo Core to exactly regulate the pipes to 90°. The Tool is partly built on the...

------------------------------------------- Solid extension of the stand for the Andonstar AD407 camera microscope, which is unfortunately quite a bit too flimsy. Only the adapter is 3d printed. Other parts needed: 1x aluminium profile 40x16 groove...

Currently I found no possibilty to adjust these intolerance, so I have realize a tool to do so. With this tool you can adjust the angle between the 2 pipes of the Primo Core to exactly regulate the pipes to 90°. The Tool is partly built on the...

Then the rest of the actual files you print in TPU so the gear has a nice surface to be against instead of using foam like the previous version. The bases are universal so you don't have to get rid of the entire thing if you sell/upgrade your...

Thank you once again for giving me the opportunity to help, and I hope we can collaborate successfully in the future! assistant It was a pleasure assisting you, and I'm glad I could be of help. If there's anything else you need or if you have any...

Sometimes fuel filler in our cars is so deep in to body that it is nearly impossible to fill them with petrol anywhere else than petrol/gas station.It comes with a small vent/breather that should help with the flow.It is available in 3 lenghts, 80 ,...

Make sure you have fontmetricsdata.scad and fontmetrics.scad in your current directory and that you start your code with use ; Public modules: * drawWrappedText(text,font="Liberation...

No supports, brims, or skirts needed.] These tools will be required for my final puzzle box assembly. These tools will be redesigned after my series of testing. Some of the small sizes printed in plastic won't be terribly functional :) unless you use...

Attach the 2" to 1 1/2" reducers to the Vent Cover, caulk around them for a tight seal, and use clear caulking that turns invisible. The caulking will also hold the fittings onto the cover as they do not fit super tight. Wait for the caulking to...