machine design njit 3d models

  The two step design means the same parts work on MTB or road tyres. Optional TPU feet to grip the garage floor. Parts RequiredYou’ll need approx. 3m of 16mm tube per bike – I used curtain rod from Bunning for all the short pieces.  It's cheap and...

molten filament and drill a 3mm hole for the screw.The holes are designed to have one full layer in the middle. This helps with bridging. Just punch through this layer with something pointy.</li><li>If the spacer isn't perfectly fixed in place, you...

I think this design is OK as is but could still be improved with some software tweaks as I learn more about how to best generate these files for improved performance. Specifically these projections would benefit from being more bowl shaped to...

Got fed up with the ziptie holding the trackhat clip to my RIG 500 headset so I got off my butt and put some effort in and design my first thingy... finally. Actually works waaaay better than I thought it would. Snug fit for the trackhat clip and...

Teddy Bear is a top-of-the-line model designed to bring even more authenticity and sophistication to your 3D rendering projects. With a high resolution 3D scan, thoroughly retopologized and unwrapped for crisp detail. It's precise enough for up-close...

The nut holes are designed to hold M2.5 nuts by friction but gluing them in just in case is a good idea. I need 5 M2.5 x 8mm screws and 7 M2.5 nuts (minus the camera part). The 18650 socket comes from https://www.thingiverse.com/thing:456900 by enif....

Got fed up with the ziptie holding the trackhat clip to my RIG 500 headset so I got off my butt and put some effort in and design my first thingy... finally. Actually works waaaay better than I thought it would. Snug fit for the trackhat clip and...

I decided to use 608 bearings and designed some threaded clips to align the pulleys, keep them in place and to allow for fast rearrangement of the pulleys when putting in a spool with different width. In addition I was unhappy with how most spools...

The front cowls are designed to fit onto a piece of aluminum channel on the front of the tank, which also holds the suspension block and a standard MG996 180-degree servo for opening the shuttle bay doors with a gear drive and arms. The loops on top...

I have designed this air purifier for my network cabinet turned printer enclosure. It uses an activated charcoal mat and a HEPA filter to remove any unwanted organic compounds and ultra fine particles from the printing process.</p><p>It is important...

It should remain loose enough for the hinge to move freely Other Suggested Items Filament Management System Hanging Mount for Rubbermaid 21 cup Drybox Hanging Side Mount Spool Skate Drybox Desiccant Dome PTFE Tube Cap PC4 - M10 Cap Double Stack...

A considerable share going toward creating ornaments such as pieces that will later adorn on fingers as part of various artistic designs giving Gold some level significance. Some uses can be noticed when a coin's worth falls under pressure; they've...

A note worth mentioning: Although comprehensive in design, certain structures have been excluded due to OSM import restrictions and inconsistencies. Consequently, users are directed to refer to included preview images displaying the actual covered...

Updated: I noticed a problem with durability causing cracking when tightening (due to the high pressure) so I've updated the design. Best printed with PETG at 100% infill. The larger version (stl and 3mf included) are specifically sized for the...

This thing was designed with Tinkercad. Edit it online at https://www.tinkercad.com/things/gznEz2Bl15G. It needs to be printed using a 0.2mm nozzle and requires assembly after printing. See the image for assembly tips. Print Settings: Rafts:...

This is by design because I'm do think people will just hold the cover to lift up the whole unit. No good. No wiring trunks and holes in STL. Go ahead DIY. Notes: -Use any filter you trust. Personally I use [3M Filtrete™ (Air Cleaning Filter - Ultra...

Chemistry modelling sets can help us visualize molecules in meaningful ways.This kit is designed with 3D printing in mind and to be displayed on a flat surface, much like we draw molecules on paper. By inserting small magnets, you can also attach...

... gets more difficult to turn, and then reheat to continue. After the parts are threaded, sand off the material thrown up on the back side of the slider. If done carefully, there won't be much or any material to remove. How I Designed This Sketchup

This is a scale prop of the cybersword from the Mega Man Battle Network series on the Gameboy Advance designed with led lighting of the blade in mind. Note: Currently I have not printed the whole blade so I can't 100% confirm that there won't be...

The filter is a fairly tight fit in the filter shell, but that is by design. The Flintar filters have two fabric tabs to help pull it out. The filter cap has 4 slots that twist on and are held by the 4 tabs on the filter housing. ...It's mostly...

This allows for super compact hotend cover and cooling nozzle design without any protruding rear fans or other odd solutions. This is the only way to combine the desired features and so far looks like nobody yet attempted such approach. -...

So I set out to design an actively cooled rack mount solution that retained the lights on the front and provided options for keystones for front cable routing.Hardware InformationThis is a general recommendation for how I did it. I purposely left...

Copper can also bring side effects when not handled properly during extraction; thus government safety regulation provides designated work guidelines for workplace usage including daily permissible exposure (1 mg/m^3 average within an eight-hour...

Every detail has been painstakingly worked by our artists, who have also designed the tiles to ensure repetition of patterns are minimized as much as possible on each miniature/model in the INSTADUNGEON™ series. LET EACH TILE'S PHYSICALITY IMPACT...

***Thing BOM: 1@ optical endstop: https://www.amazon.com/gp/product/B081W4KMHC/ 3@ 688 size ball bearings 2@ M3-8 3@ M3-16 7@ M3-10 1@ M3 nylock nut 1@ printed lowerBox 1@ printed upperBox 1@ printed shaft 1@ printed armLeft 1@ printed armRight 1@...

We can use that to connect LEDs parallel to it, and thanks to their property of passing current in only one direction we can connect two colours in oposit directions to indicate motor direction.Design is not limited to escalator model, this can be...

I have designed these to work for the MCS Tacamo: Hurricane, BOLT, blizzard, storm 2 but it should work for other markers as well. this not made to be used in a DYE dam or PE EMF100… since they can work with stock PE followers. and there is no need...

DIY Ford Puma WRC Steering wheel Srh-europe design 1:1 Proportional with the real Ford Puma WRC Steering Wheel Build your own high quality Ford Puma WRC for your simulator. PARTS REQUIRED: 0.96inch display(1pcs): ...

To print this design, follow these instructions with the given options: - Picture options: [0.671, 0.702, 0.686, 0.753, 0.698, 0.749, 0.769, 0.753, 0.698, 0.741, 0.749, 0.769, 0.761, 0.706, 0.718, 0.745, 0.745, 0.796, 0.761, 0.769, 0.725, 0.725,...

The rest is designed to work without any. Since the LED or other electronics shouldn't get hot, any material is fine. Custom Section Needed Vitamins In addition to the printed parts, you will need: 2x regular 5mm LEDs 1x 9V battery 1x a resistor...