mabel grappling hook 3d models

An added frustration was if I was out and about, that meant I had to carry and keep track of an extra case, plus the piece that the Junglecat hooks into when not on the phone. I'm not that organized. So, I decided to come up with an original...

(Mini maps!) Let everyone grab tiles and build your world cooperatively! -Have adventure hooks prepared for different unique location tiles, let players replace Mystery tiles on your map from a random draw bag maybe, who knows? If you want to make...

Small hooks ensure that the pictures do not fall over.  At the end you only have to put the lid on and your oil lamp is ready.Now all you have to do is carefully lift the lamp and turn on the LED chain. Find a suitable place where everyone...

... There are also useful coat hangers and finger toys.Or just check out all my creations.ThanksThanks go to jake for the photo of the “Keep calm and have a beer” version!

 No supports.Assembly of the phone clamp should be fairly obvious.  Use superglue (CA) or 2-part epoxy to attach the 2 main_clamp_hinges to the base, sandwiching the 2 hinge_plugs to locate them.Tap M6 nuts into the 2 knob parts.Use...

Slide it in next to the left side of the hammer, behind the Pawl and hook the curved spring part around the hammer axis screw and press it into place such that the bottom of the rectangular plate is flush with the bottom of the slot on the...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

The hooks are great but in the double claw you have too little leverage to keep the claw closed. This is true for all the hooks. There lots of ways to increase leverage at the end of the gripper such as a mod on this...

I printed them at 20mm (4 hours or so,) but they look even better at 15mm.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version.Currently set at 75% size to reduce build time. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

Take what's theirs and make it your own! More Armour!Demolior Class Heavy Tank - https://www.printables.com/model/135967-tank-demolior-class-heavy-deathhead-ii-model-scien Scopulus Class Heavy Tank -...

This ones for you guys! Video: William of Materials: 1 64mm M8 bolt and nut 1 64mm M5 bolt and nut 5 m3 10mm cone head screw with 2 nuts (non locking) 8 14mm M3 cone head screws 4x 14x5x5 bearings 2x 608zz bearings 2x m8 washers a metric crapton...

Non-printed parts neededBT-60 Body tube - 106mm lengthBT-50 Body tube - 79mm lengthPlastic Parachute - 24" should do it (unknown)Standard Estes Motor HookSmall pan head screwsLaunch LugOptional stuff Note: I consider these optional because there...

The 3D printing model's chosen scale is 1:544 for the FFF/FDM version and 1:1088 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 66 parts;- A printed ship is 584 mm tall, 367 mm wide, 367 mm...

(Support on the build plate only.)Scale's easily if you want a larger or smaller version. Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

It also made my wrist hurt.The hooks are great but in the double claw you have too little leverage to keep the claw closed. This is true for all the hooks. There lots of ways to increase leverage at the end of the gripper such as a mod on this <a...

* My panels started to fall off the wall when one of the wall hooks gave way (failure of the adheasive holding it), so I updated the design to have a hole to add a 14 gauge nail. You may need to run a drill though it if your nails do not fit, I did...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Finally, take your small rubber band and loop it around the hooks on the RearFrameLockBarPlate and stretch it around the semicircular notch on the hammer. This should allow the hammer to return after being cocked back. Barrel Frame Assembly Gather...

Hook the filament from the outisde roll into the filament guide.rnrnThe filament guide's purpose (as with the stock guide) is to keep the outside filament strand from interfering with the inside roll.rnrnThe outside roll typically goes to...

The 3D printing model’s chosen scales are 1:68 for the FFF/FDM version and 1:136 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 83 parts;- A printed model is 210 mm tall, 589 mm wide, 467 mm deep;- A printed...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.Enforced supports are required on verticle pipes (see files).Superglue the valve handles.Start pumping that...

&nbsp;This will move the tube stop to the proper location and you can then glue it in place.&nbsp;Non-printed parts needed2 - BT-50 Body tube &nbsp;60mm (motor tube) and 194 mm (main tube)Plastic Parachute (not sure what size just yet)Standard Estes...

Two eyelets, one at each end of the fixture, allow operators to attach safety hooks to the fixture during installation. Operators bring flex conduit down to the threaded mounting hub. ...Customer provided wiring is fed down through the flex conduit to...

Here I'm using a bench power supply, but you can test with the supply you intend to use. Now you can install your lights on your printer and hook up the power. In this picture I have made a basic power switch and a splitter cable to power two of...

I used an old 3D printer controller board (Printrboard) I had lying around, hooking up one module to the X and Y axes and the other to the Z and E axes. You can then just start sending G-code commands at the controller to make things move.</p><p>Also...

due to possible differences between boards, it's designed to hook around the board/port, and "float" over the opening in the case * Because of differences in USB cables... you may have problems with certain cables not plugging in all the way with...

You need to use one of the charging cables to hook the battery to the motor through the switch. The switch is from a tea light. The battery is just stuffed in the boiler. The switch is on top of the boiler. You can access the connector for the...