m6 to m10 thread adapter 3d models

M10x1 (male) to M6x1 (female) adapter.It was a little tight so I had to run a M6 tap to clean the inside treads.

It's likely you'll have to work on re-threading the entire operation.

I'm attempting to replace the PTFE tube on my Anet E10 printer, but so far, I've managed to break the PC4-M6 fitting. Unfortunately, it's not holding onto the tube securely. ...Luckily, I have a spare PC4-M10 fitting lying around, which I'll be using as...

... Trockenbox gekauft. Da diese leider nur auf der Oberseite 2 Auslässe hat, wollte ich das ganze etwas optimieren. Also auf jeder Seite 2 Teflonschläuche. Da ich leider nur noch je 2x M6 und M10 Kupplungen hatte, hab ich diesen Adapter entworfen.

M10x1.5 to M16x2 thread adapter for gear shift knob Thread adapter M10x1.5 to M16x2 for gear shifter knob

Female PC4 connector to male M6 adapter, crafted by combining elements from prior designs due to an unexpected shortage of male M10 connectors.

...This Facilitates the Replacement of Standard PC4-M6 on the Extruder Side with a More Common M10 Fitting Typically Used on the Hotend. This Solution May Be Temporary and Beneficial for Those Without Spare M6 Fittings but Possessing Access to M10 Ones.

... standard PC4-M6 fitting with the more common PC4_M10 fitting typically used on the hotend. This upgrade can be particularly useful as a temporary solution for individuals who lack spare M6 fittings but happen to have M10 fittings readily available.

It takes a PC4-M10 pushfit, like the one on the Chinese E3D bowden version, and screws onto a M6 thread of the MK7 (MK8) extruder. I'm not sure if it will be strong enough. The weakest point is between the M6 thread and the M10 section. For the long...

It takes a PC4-M10 pushfit (like the one on the china E3D bowden version) and screws on a M6 thread of the MK7 (MK8?) extruder. I don't know if it will be strong enough. The weakest point is between the M6 thread and the M10 section. For the long...

Installing the Bowden fitting adapter PC4-M6 to PC4-M10 is a straightforward process that enables you to connect your hotend's PC4-M10 fitting directly to the extruder side of your printer. This adapter is particularly useful when you're in a pinch...

Practical Thread Comparison Tool for m6, m8, and m10 Threads

Print thread side up, 0.1-0.2mm layers, whatever fill required for a very simple part intended to replace the M10 threaded push-to-connect tubing adapter seamlessly. ...Make any requests and I can create one that fits more recessed into the heatsink...

... it was not designed to hold one. The pics show the repair process. The CAD modeling was just a few circles and the Fusion360 Thread tool. Big thanks to Zach at https://amigoframeworks.com for talking me off the ledge and helping with this idea.

M10 has an outer diameter of 10mm and a pitch of 1.5mm.The fittings have a (R) G 1/8" thread, almost 10mm on the outside but a pitch of 0.907mm.I don't want to say that the fittings aren't available with larger Metric threads. ...But so far, in...

Don't be like me, don't break a Bondtech Dual geared extruder trying to screw a plastic thread adapter directly to the 89 euros piece.This adapter was made so you can screw it in the brass piece that usually comes with the extruder and can attach a...

To get started, you'll need the throat of an E3D V6/Volcano hotend (or its clones) that matches perfectly with either the PC4-01 or a PC4-M10 fitting. Since this printed component won't directly interact with the filament, there's no risk of...

A Custom Bowden Coupler Adapter for the PC4-M10 and PC4-M6 Straight Male Pneufit Remixed from Model Number 2208165, Created by Mightynozzle

Printed at 100% infill to be strong, 3 perimeters 

This is a way to allow printing using a filament while it is still in a drybox.Just drill a 1/2in (~13mm) hole in the drybox and put this in it. ...There is a version for both the M6 and M10 PTFE push fitings.

m5(female) to m6(male) adapter for extruder... Bare in mind that those threads are not make up to specs, they are a bit off to allow error for a printer, generally speaking should work. ...Print with hex nut down and no support, might require a bit of...

Adapter to use bowden hotend in mk8 direct drive extruder

Male-to-male adapter designed specifically for an extruder...\r\n\r\nKeep in mind that those threads do not conform to standard specifications; they are intentionally slightly off to accommodate potential errors in printer calibration, which should...

So I designed a quick fix adapter while I wait for the metal part to arrive. Print Settings Printer Brand: RepRap Printer: Geeetech Prusa i3 Aluminium Rafts: No Supports: No Resolution: 0.1 Infill: 30% + Notes: I suggest using no infill, even though...

... which is infamous for its weak grasp on the Teflon tube. Next, apply a strong adhesive to the area where the PC4-M6 or PC4-M10 fits into the printed part. ...On the fitting itself, I added stripes that securely hold the bowden tube in place.

The ultimate Christmas gift for the community!\nA replacement print for bowden coupling PC4-M6 or PC4-M10, compatible with heatsink or another printer part.\nYou may need to do some light filing on the printed part using a 4mm drill...

Adapter M10 male to m6 female tollerance is ok for resin printer

See https://www.thingiverse.com/thing:1993384. ... These repaired files come from the same link, but were rebuilt using NetFabb and exported as Binary STLs. Problem: The original PC4-M6 and PC4-M10 files had some mesh problems. ... Have a great day!

I intended it to work on both sides (M3, M4 on one and M5, M6 on the other; the hex bit fits on both sides), but the one side works fine for all four types of thread taps. When clamping the part there is a lot of flex, therefore **I strongly...

I created it because I only have a hand drill with an HEX-Insert and did not want to buy specialised taps.I intended it to work on both sides (M3, M4 on one and M5, M6 on the other; the hex bit fits on both sides), but the one side works fine for all...